Need help?Do you have a question about the Crate EXCALIBUR GX-2200H and is the answer not in the manual?
Power| input power requirements | 120VAC, 60Hz, 240 watts max. |
|---|---|
| output power rating | 90 watts RMS @ 5% THD, 2 ohm load |
| fuse rating and type | 2A Normal Blo, 250V Internal, 100VAC-120VAC; 1A Slo Blo, 250V Internal, 230 VAC |
Audio Specifications| maximum input signal level accepted | 8 volts peak to peak |
|---|---|
| input impedance | 470 k ohms |
| total system gain, channel B | 54 dB @ 1 kHz, all controls at “10”, Bright off |
| total system gain, channel A, gain one | 69 dB @ 1 kHz, all controls at “10” |
| total system gain, channel A, gain two | 86 dB @ 1 kHz, all controls at “10” |
Weight and Dimensions| cabinet size | 11.63” H x 30.75” W x 11” D |
|---|---|
| weight | 35 lbs. |
Power| input power requirements | 120VAC, 60Hz, 500 watts max. |
|---|---|
| output power rating | 220 watts RMS @ 5% THD, 2 ohm load |
| fuse rating and type | 5A Normal Blo, 250V Internal, 100VAC-120VAC; 3A Normal Blo, 250V Internal, 230VAC |
Audio Specifications| maximum input signal level accepted | 8 volts peak to peak |
|---|---|
| input impedance | 470 k ohms |
| total system gain, channel B | 54 dB @ 1 kHz, all controls at “10”, Bright off |
| total system gain, channel A, gain one | 69 dB @ 1 kHz, all controls at “10” |
| total system gain, channel A, gain two | 86 dB @ 1 kHz, all controls at “10” |
Weight and Dimensions| cabinet size | 11.63” H x 30.75” W x 11” D |
|---|---|
| weight | 35 lbs. |
Overview of the Crate GX-900H/GX-2200H Excalibur Series guitar amplifiers, highlighting their design and capabilities.
Highlights of the amplifier's features, including solid-state circuitry, separate channels, dual gain controls, and effects loop.
Connection point for guitar or wireless receiver using a mono 1/4" plug.
Controls for the distortion channel including Gain One, Gain Two, Low, Mid, High EQ, and Level.
Switch for selecting clean/distortion channels and controls for clean channel EQ (Low, Mid, High) and Level.
Boosts upper frequencies on the clean channel for added brightness and clarity.
Separate reverb level adjustments for Channel A (distortion) and Channel B (clean).
Jack for footswitch connection and the main power switch with an indicator LED.
Line Out sends signal to effects; Line In receives signal from effects or acts as a direct feed.
Connects to speaker cabinets via mono 1/4" plugs, wired in parallel, minimum 2-ohm load.
Connects to a grounded AC power outlet; essential to use a grounded outlet.
Suggested control settings for achieving clean guitar tones, with variations for Strat-style guitars.
Suggested control settings for 'dirty blues' and 'grungy' guitar sounds.
Suggested control settings for classic hard rock, heavy metal, and high-energy 'mosh pit' tones.
Diagram illustrating the internal signal flow from input buffer through channels, EQ, effects loop, and power amp to speaker output.
Details maximum input signal level, input power requirements (voltage, wattage), and input impedance.
Information on total system gain for Channel B and Channel A (Gain One/Two), and output power ratings.
Specifies the frequency range and dB adjustments for Low, Mid, High, and Bright controls on both channels.
Lists fuse ratings, cabinet dimensions, weight, and cleaning instructions for the amplifier.
To Next Page
