To Next PageTo Next Page
Need help?Do you have a question about the CROSSRC EMOX2 and is the answer not in the manual?
Check screws, battery voltage, motor, and servo direction before operating the vehicle.
Power off receiver before transmitter, handle hot components with care, and avoid damaged battery packs.
Assemble the main gearbox housing with various gears and shafts.
Continue gearbox assembly, incorporating more gears and drive components.
Instructions on how to adjust the limited slip differential for different battery types.
Information on final reduction ratio based on motor gear selection.
Attach the motor and gearbox assembly to the chassis.
Test the gear mesh by connecting the ESC to the motor/gearbox assembly.
Assemble the driveshafts using specified components and thread lock.
Connect the assembled driveshafts to the gearbox assembly.
Attach various suspension and drivetrain mounting brackets to the chassis frame.
Install the main chassis rails and support structures.
Mount electronic components like the ESC and receiver box to the chassis.
Install the shock absorbers onto the chassis assembly.
Assemble the shock body, piston, and spring components.
Connect the assembled shocks to their respective mounting points.
Assemble the front differential gear housing and internal components.
Assemble the rear differential gear housing and internal components.
Assemble and install the front steering knuckle components.
Connect the steering linkage rods to the knuckles and servo saver.
Assemble the front differential housing with gears and shafts.
Install axle shafts and universal joint connectors.
Assemble the rear differential housing with gears and shafts.
Install rear axle shafts and universal joint connectors.
Assemble the front axle housings and internal components.
Assemble the rear axle housings and internal components.
Install differential gears and related components into housings.
Connect drive shafts to the differential outputs.
Install the upper and lower suspension linkage rods of various lengths.
Attach the front suspension links to the chassis and steering knuckles.
Install chassis reinforcement and mounting brackets.
Mount the wheels onto the vehicle's axles.
Install shock towers and associated mounting hardware.
Attach the body mount brackets to the chassis frame.
Install the front and rear fender components.
Attach the lower body panels and trim pieces to the chassis.
Mount the steering and other servos to their respective locations.
Install the Electronic Speed Controller (ESC) and receiver box.
Connect and adjust the steering servo linkage for correct operation.
Install body support brackets onto the chassis.
Set the steering servo trim to the neutral position before connecting.
Securely attach the wheels to the vehicle's axles.
Connect the steering servo, ESC, and other electronic components as shown.
Wash the inside of the body shell, then mask windows before painting.
Apply polycarbonate spray paints, then remove masking and protective films.
Wash and dry the body shell, then apply polycarbonate spray paints.
Remove masking and peel off external protective films after painting.
Attach the rear spoiler and its mounting components to the body shell.
Install side body panels and brackets to the main body structure.
Mount rear frame sections and support structures onto the body.
Attach the ladder and associated mounting brackets to the rear body.
Attach various body mounting brackets to the chassis frame.
Assemble and attach brackets for headlights and taillights.
Install mounting hardware for the front bumper assembly.
Mount the roof rack system onto the vehicle body.
Attach the rear bed structure and associated components.
Install side frame supports and crossmembers onto the chassis.
Mount the electronic component tray onto the chassis.
Attach accessory mounting plates to the vehicle body.
Adjust the differential lock mechanism to the 'Lock' or 'Unlock' position.
Assemble and install front and rear suspension linkage rods of various lengths.
General| Scale | 1/10 |
|---|---|
| Wheelbase | 313mm |
| Drive Type | 4WD |
| Motor Type | Brushed |
| Battery Type | LiPo |
| Suspension | 4-Link |
| Shock Absorbers | Oil-filled |
| Tire Type | All-Terrain |
| ESC | 45A Brushed ESC |
| Radio System | 2.4GHz |
| Servo | Not Included |
| Waterproof | Yes |
