To Next PageTo Next PageWhy is the thermal indicator on my Crown Amplifier?
If the Crown Amplifier is overheating, allow it to cool down. Make sure that the loads are not less than 2 ohms, and that the input levels aren't excessive. Also, verify that the ventilation is sufficient and the mode-switch setting is correct.
What to do if my Crown CTs 600 has distorted sound?
If your Crown Amplifier's sound is distorted, check if the load is wired correctly and that the Stereo/Mono mode switch is set correctly. Also, if the input is overloaded by a signal level that is too high, turn down your amplifier level controls, or turn down the input signal, until the clip light goes out.
How to fix a Crown CTs 600 when the power indicator is off?
If the power indicator is off on your Crown Amplifier, it could be due to several reasons. The amplifier might have lost AC power, or the Power switch might be off. Ensure the amplifier is properly plugged into the power receptacle. If the amplifier output level is too high, allow the unit to cool, turn down the Level controls, and press the Reset Switch on the back panel.
What to do if Crown Amplifier has no sound but has power?
If there is no sound from your Crown Amplifier, even though it has power, the Power LED is on without flashing, and the amp is receiving an input signal while the Signal indicator is flashing, check the speaker connections. The speakers may not be connected, or there may be an open circuit due to speaker failure. Also, check for a short on the amplifier output by disconnecting your speakers from the affected channel(s) one by one to determine if one of the loads is shorted.
Why is the power indicator flashing on my Crown CTs 600 Amplifier?
If the power indicator on your Crown Amplifier is flashing, it means that the AC line voltage has dropped below 20% or has risen above 10% of the nominal line voltage of the power supply.
What to do if Crown CTs 600 has no input signal?
If your Crown Amplifier has no input signal and the signal indicator isn't flashing even though audio is applied and the channel is ready, it could be because the input signal level is very low, or the level controls are turned down.
What does it mean if the fault indicator is flashing on my Crown Amplifier?
If the Fault indicator is flashing on your Crown Amplifier, the amplifier channel has stopped operating. Refer the unit to an authorized Crown Service Center.
Why is the data indicator not flashing on my Crown CTs 600 Amplifier?
If the Data indicator is not flashing on your Crown Amplifier, even though the PIP module is installed and the host computer IQ software is active, the cable between the computer and the PIP module may be broken or not connected.
General| Channels | 2 |
|---|---|
| Power Output (8 Ohms) | 300W per channel |
| Power Output (4 Ohms) | 600W per channel |
| Total Harmonic Distortion (THD) | < 0.05% |
| Damping Factor | > 500 |
| Input Sensitivity | 1.4V |
| Signal to Noise Ratio | > 100 dB |
| Frequency Response | 20 Hz - 20 kHz |
| Dimensions (H x W x D) | 3.5" x 19" x 15.5" |
| Weight | 19 lb (8.6 kg) |
| Input Impedance | 20k Ohms |
| Power Requirements | 100V-240V ±10% 50/60 Hz |
| Cooling | Continuously variable speed forced air |
Wiring for stereo dual-channel constant voltage operation.
Wiring for mono input signal to stereo outputs.
Specific wiring for stereo dual-channel operation at 8, 4, or 2 ohms.
Wiring for mono bridged constant voltage operation.
Specific wiring for mono bridged operation at 16, 8, or 4 ohms.
Front panel details for multi-channel units.
Back panel details for multi-channel units.
Protection systems overview.
Addresses problems related to the power indicator status.
System wiring overview for multi-channel units.
AC connection for multi-channel units.
Installation and placement for multi-channel units.
Output wiring for multi-channel units.
Startup sequence for multi-channel units.
Cooling requirements for multi-channel units.
