To Next PageTo Next Page
Need help?Do you have a question about the Crown CTs 8200 and is the answer not in the manual?
General| Power Output (4 ohms Stereo) | 200W per channel |
|---|---|
| Power Output (8 ohms Bridged-Mono) | 400W |
| Damping Factor | > 200 |
| Input Sensitivity | 1.4V |
| Signal-to-Noise Ratio | > 100dB |
| Channels | 2 |
| Frequency Response | 20Hz - 20kHz |
| Dimensions | 19" x 3.5" x 16.2" |
| Weight | 28 lbs |
| Input Impedance | 10 kOhms |
| Power Requirements | 100V-240V, 50/60 Hz |
Numbered safety instructions for operating the amplifier safely.
Statement regarding compliance with FCC rules for RF emissions.
Visual identification of CTs 600, CTs 1200, CTs 2000, and CTs 3000 models.
List of EMC and safety standards the product conforms to.
Highlights of the amplifier's design and capabilities.
Guidance on using the manual and obtaining additional support.
Instructions for unpacking, inspecting, and installing the amplifier.
Guidelines for rack mounting and ensuring proper airflow.
Guidance on selecting and connecting input and output wires.
Instructions for wiring in Dual 8/4/2 and Bridge-Mono 16/8/4 modes.
Instructions for wiring in Dual 70V/100V and Bridge-Mono 140V/200V modes.
Procedure for setting up Dual Mode using a Y Input.
Steps for connecting to AC mains and initial startup.
Important safety and performance precautions during operation.
Description of Signal, Clip, Ready, Thermal, and Fault indicators.
Description of Power, Data, Bridge Mode, and Power Switch.
Details on AC power connector, ventilation, and accessory panel.
Description of input connectors, output connectors, and mode switch.
Overview of amplifier protection features like TLC, JTS, and Fault.
Overview of features like Switching Power Supply and Input Compressor.
Details on selecting input sensitivity levels for channels.
Information on optional accessories like VCA modules.
Table showing attenuation levels for level control detents.
Diagnosing issues related to power and fault indicators.
Troubleshooting distorted sound and thermal indicator problems.
Diagnosing issues when there is no sound or no input signal.
Troubleshooting thermal and bridge LED indicator statuses.
Table detailing minimum guaranteed power output for models.
Table of performance metrics like frequency response and THD.
Specifications for load impedance and voltage gain.
Physical dimensions, weight, and cooling system specifications.
Table detailing AC power draw and thermal dissipation for CTs 600.
Table detailing AC power draw and thermal dissipation for CTs 1200.
Table detailing AC power draw and thermal dissipation for CTs 2000.
Table detailing AC power draw and thermal dissipation for CTs 3000.
Visual identification of CTs 4200 and CTs 8200 models.
List of EMC and safety standards for multi-channel units.
Power ratings and key features for CTs 4200 and CTs 8200.
Guidance on using the manual for multi-channel amplifiers.
Setup steps for unpacking and installing multi-channel units.
Guidelines for rack mounting and cooling multi-channel units.
Instructions for wiring inputs and outputs on multi-channel units.
Instructions for Dual 8/4 and Dual 70V wiring modes.
Instructions for Bridge-Mono 16/8 and 100V wiring modes.
Connecting multi-channel units to AC power and startup.
Essential precautions for safe and optimal amplifier operation.
Description of channel-specific status indicators (Signal, Clip, Thermal, Fault).
Description of system-wide controls and indicators (Power, Data, Bridge).
Details on power connector, ventilation, and accessory panel for multi-channel units.
Description of input/output connectors and mode selection for multi-channel units.
In-depth explanation of protection systems like TLC, FIT, and Voltage Protection.
In-depth explanation of features like Switching Power Supply and Mode Switch.
Table showing attenuation levels per detent for channel level controls.
Information on VCA-MC modules for remote level control.
Details on available input sensitivity settings and options.
Diagnosing power, fault, and distorted sound issues.
Troubleshooting thermal indicators and other status indicators.
Diagnosing issues related to no sound or missing input signals.
Troubleshooting thermal and bridge LED indicator statuses.
Table detailing guaranteed power output for CTs 4200/8200.
Table of performance metrics for CTs 4200/8200.
Specifications for load impedance and voltage gain.
Physical dimensions, weight, and cooling specs for CTs 4200/8200.
Table detailing AC power draw and thermal dissipation for CTs 4200.
Table detailing AC power draw and thermal dissipation for CTs 8200.
Information on obtaining service internationally and in the US.
Guidelines for returning products for factory service.
Summary of warranty coverage and items excluded.
Details on warranty terms, limitations, and legal remedies.
Procedures for obtaining warranty service outside the USA and Canada.
Sections for owner details and product purchase information.
Sections for product return details and payment methods.
