What to do if my Crown CTs sound is distorted?
If your Crown Amplifier produces distorted sound, check if the load is wired correctly or if the Stereo/Mono mode switch is set correctly. Also, the input might be overloaded by a signal level that is too high. In this case, turn down your amplifier level controls, or turn down the input signal, until the clip light goes out.
Why my Crown CTs Amplifier has no sound?
If your Crown Amplifier has no sound even though it has power, ensure the speakers are connected. If they are, diagnose and replace any failed speaker. Also, check for a short on the amplifier output by disconnecting your speakers from the affected channel(s) one by one to determine if one of the loads is shorted. Finally, ensure the channel has not been set to standby mode via the control system, and change the channel setting from standby mode if necessary.
How to fix a Crown CTs Amplifier with no power indicator?
If the power indicator is off on your Crown Amplifier, first check the power connections to ensure the amplifier has AC power. Then, check that the amplifier’s Power switch is on. Ensure the amplifier is plugged into the power receptacle. If the amplifier output level is too high, allow the unit to cool, turn down the Level controls, and press the Reset Switch on the back panel.
What to do if the thermal indicator is on Crown CTs Amplifier?
If the thermal indicator is on for your Crown Amplifier, allow the amplifier to cool. Check for loads less than 2 ohms and for excessive input levels. Also, check for proper ventilation and proper mode-switch setting.
Why is the power indicator flashing on my Crown CTs Amplifier?
If the Crown Amplifier's power indicator is flashing, it means the AC line voltage has dropped below 20% or has risen above 10% of the nominal line voltage of the power supply.
What to do if Crown Amplifier has no input signal?
If there is no input signal and the signal indicator is not flashing on your Crown Amplifier, even though audio is applied and the channel is ready, increase the input signal level. Also, ensure that the level controls are not turned down; if they are, turn them up.
Why is the data indicator not flashing on my Crown CTs?
If the data indicator is not flashing on your Crown Amplifier, even though the PIP module is installed and host computer control software is active, check and reconnect the cable between the computer and PIP module.
CTs Series amplifiers require Class 2 output wiring for safe operation.
Warning about high power density creating a strong magnetic field affecting nearby sensitive equipment.
Recommendations for safely installing the amplifier and ensuring adequate airflow.
Instructions for wiring in Dual 8/4/2 and Dual 70V/100V modes.
Instructions for wiring in Bridge-Mono 16/8/4 and Bridge-Mono 140V/200V modes.
Steps for connecting the amplifier to the AC power source, including voltage warnings.
Step-by-step guide for safely turning on and configuring the amplifier for initial use.
Detailed explanation of all front panel buttons, LEDs, and their functions.
Description of rear panel inputs, outputs, switches, and connectors.
Details on various protection circuits like TLC, JTS, Fault, and voltage protection.
Diagnosing problems when the power indicator is off or flashing.
Troubleshooting distorted sound, fault indicators, and thermal issues.
Steps for connecting to AC power and performing the initial startup procedure.
Addressing distorted sound, thermal issues, and mode switch conflicts.
Detailed instructions for returning units for factory service, including packing and SRA.
General| Power Output | Varies by model (CTs 4200, CTs 3000, CTs 2000, CTs 1200, CTs 600) |
|---|---|
| Total Harmonic Distortion | < 0.05% (at full rated power) |
| Input Sensitivity | 1.4V for rated power |
| Weight | Varies by model (e.g., CTs 2000: 25 lbs) |
| Channels | 2 |
| 8 Ohm Stereo (per channel) | Varies by model |
| 4 Ohm Stereo (per channel) | Varies by model |
| 2 Ohm Stereo (per channel) | Varies by model |
| 8 Ohm Bridge-Mono | Varies by model |
| 4 Ohm Bridge-Mono | Varies by model |
| Voltage Gain | 32dB |
| Damping Factor | >500 |
| Cooling | Variable-speed fan |
To Next Page
