Crown Macro-Tech MA-2400 - Output Module Parts Lists; Q42670-2 Output Module Components

Macro-Tech 2400 Amplifier Service Manual
25
Q42670-2 Output Module (P10233-8 board) Parts List
Capacitors
C01 C 3978-1 .047µF
C02 C 2938-6 .1µF
C03 C 2938-6 .1µF
C04 C 6806-1 .01µF
C05 C 6806-1 .01µF
C06 C 6806-1 .01µF
C07 C 6807-9 .001µF
C08 C 6810-3 180pF
C09 C 6809-5 220pF
Diodes
D01 C 2851-1 1N4004
D02 C 2851-1 1N4004
D03 C 2851-1 1N4004
D04 C 2851-1 1N4004
D05 C 2941-0 1N5402
D06 C 2941-0 1N5402
D07 C 2941-0 1N5402
D08 C 2941-0 1N5402
D09 C 2851-1 1N4004
D10 C 2851-1 1N4004
D11 C 2851-1 1N4004
D12 C 2851-1 1N4004
Inductors
L00 C 6592-6 Output Coil
L01 C 3510-2 470µH
L02 C 3510-2 470µH
Transistors
Q17 C 7271-7 NPN MPSU10
Q19 C 7318-6 PNP MPSU60
Note: Output Transistors, Driver Transistors, Q18, and
S100/200 are not included with the module assembly.
Refer to the Output Assembly Parts List on pages 17
and 18 for these part numbers.
Resistors
R00 A10266-4711 470
R01 A10266-1011 100
R02 C 7778-1 5.6 .5W Flame Proof
R03 D 6486-2 .2 5W
R04 D 6486-2 .2 5W
R05 D 6486-2 .2 5W
R06 D 6486-2 .2 5W
R07 D 6486-2 .2 5W
R08 D 6486-2 .2 5W
R09 C 7779-9 22 .5W Flame Proof
R10 A10266-1011 100
R11 C 7317-8 2.7 5W
R12 A10266-2R73 2.7 1W
R13 A10266-4711 470
R14 A10266-2R73 2.7 1W
R15 D 6486-2 .2 5W
R16 D 6486-2 .2 5W
R17 D 6486-2 .2 5W
R18 D 6486-2 .2 5W
R19 D 6486-2 .2 5W
R20 D 6486-2 .2 5W
R21 C 7778-1 5.6 .5W Flame Proof
R22 C 7779-9 22 .5W Flame Proof
R23 C 6844-2 250 Pot LS
R24 A10266-1331 13K
R25 A10266-2221 2.2K
R26 C 6844-2 250 Pot HS
R27 A10266-3911 390
R28 A10266-1331 13K
R29 A10266-5101 51
R30* A10265-10201* 102*
Misc.
Board P10233-8
Jumpers C 5868-2 0 Ohm (Qty 5)
J500 J600 C 7057-0 10 Pin Header
*Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).