Culligan BAEMUV1SHSK SSA User Manual (English)

Questions and Answers:

M
Monica PrinceAug 2, 2025
Why is my Culligan BAEMUV1SHSK SSA not dispensing water?
- M
  matthew79Aug 2, 2025
  If your Culligan Water Dispenser isn't dispensing water, there are several possible reasons. First, ensure the dispenser is plugged into a working, grounded GFCI power outlet and that the main power supply is on. Also, make sure that the lower cabinet door is completely closed, allowing time for the pump to refill the reservoirs. Check if the water bottle is empty and replace it if needed. Verify that the connection between the water bottle cap and the connector is secure. If none of these steps work, remove the water bottle, unplug the dispenser, and contact your dealer.
C
curtis32Aug 6, 2025
Why is my Culligan BAEMUV1SHSK SSA leaking from the dispense point?
- A
  April ReedAug 6, 2025
  If water is leaking from the dispense point of your Culligan Water Dispenser, check the button area for any foreign objects that may be causing the buttons to stick. If the issue persists, it could indicate damage to the dispense point, and you should contact Culligan Customer Service at 844-787-3148.
M
Marcus GrahamAug 10, 2025
Why is my Culligan BAEMUV1SHSK SSA Water Dispenser not dispensing cold water?
- B
  Brian WatkinsAug 10, 2025
  If cold water is not dispensing from your Culligan Water Dispenser, check if the cooling system switch is turned on. If you've recently dispensed a lot of cold water, give the system about 15 minutes to cool down again. Make sure the dispenser has at least 6 inches of clearance on all sides for proper ventilation. If the problem persists, remove the water bottle, unplug the dispenser and contact your dealer.
K
Kristina SmithAug 14, 2025
Why is my Culligan BAEMUV1SHSK SSA Water Dispenser not dispensing hot water?
- A
  Amy JohnsonAug 14, 2025
  If your Culligan Water Dispenser isn't dispensing hot water, first, ensure that the hot water switch is turned on. If you have used a lot of hot water recently, allow 15 minutes for the water to reheat. If the issue continues, remove the water bottle, unplug the dispenser, and contact your dealer.
J
Joseph RomeroAug 19, 2025
What to do if Culligan BAEMUV1SHSK SSA Water Dispenser is dripping water?
- S
  Stephanie ChristensenAug 19, 2025
  If your Culligan Water Dispenser is leaking water onto the floor, check the hot tank drain cap to ensure it is properly tightened. If the seal inside the drain cap is damaged, replace it with a new one. If the dripping continues, it could indicate a leak in the hot or cold water tank, in which case you should remove the water bottle, unplug the dispenser, and contact your dealer.
J
Jeffrey HarrisAug 22, 2025
How to reduce noise from Culligan BAEMUV1SHSK SSA?
- J
  Jennifer SchultzAug 23, 2025
  If your Culligan Water Dispenser is making excessive noise, ensure it is placed on a level, flat surface. Also, check to make sure the dispenser isn't touching any other objects that could be causing vibrations.
A
Ashley TuckerAug 27, 2025
Why does my Culligan Water Dispenser water taste strange?
- R
  Randy AguilarAug 27, 2025
  If the water from your Culligan Water Dispenser has a strange taste, this is not uncommon with new dispensers and usually disappears after the first bottle has been used. If the taste persists, clean the siphon tube and waterways.

Culligan BAEMUV1SHSK SSA Specifications

General

Brand	Culligan
Model Number	BAEMUV1SHSK SSA
Product Type	Water Dispenser
Dispenser Type	Bottom Loading
Material	Stainless Steel
Voltage	110V
Power Consumption	500W
Warranty	1 year