Current Audio AMP-1270

Questions and Answers

S
Sandra TerryAug 19, 2025
What to do if there is no sound from Current Audio Amplifier?
- S
  Sarah CalhounSep 12, 2025
  If there is no sound from any channel on your Current Audio Amplifier, here are a few things to check: * Ensure the amplifier is plugged into a working, unswitched AC power outlet. * Verify all audio cables are properly connected to the correct inputs; try replacing the cable. * If using a matrix switcher, ensure it's programmed to send a signal to your input. Also, check the audio format selected on your DVD player. * Confirm the master power switch on the rear of the amplifier is in the ON position. * Check the front power switch; the light should be BLUE. Also, check if a 12 Volt Trigger is applied.
D
Darren BruceAug 21, 2025
Why is my Current Audio AMP-1270 Amplifier humming or buzzing?
- J
  Jessica HoltAug 21, 2025
  If you're experiencing hum or buzz with your Current Audio Amplifier, consider the following: * Make sure the RCA cables are fully inserted. Try replacing the cable. * The cable might be faulty, try replacing it. * Check the grounding with a plug tester. You can also try reversing the cord or using a 2-prong adapter. * If prewired cables are running too close to AC wires, insert an isolation transformer in-line with the RCA jacks.
M
Mark MathisAug 23, 2025
What to do if there is no audio from one or more channels on Current Audio AMP-1270 Amplifier?
- C
  Crystal KochAug 25, 2025
  If you're not getting audio from one or more channels on your Current Audio Amplifier, try these steps: * Check the source cable and output to ensure they are working correctly. * Verify that the Normal/Line-In switch is in the correct position. Also, check the Bridge/Normal switch position. * Inspect the speaker connections for any loose wires or shorts. Any short can cause the zone to shut down both channels.
J
jeanettesmithAug 28, 2025
How to stop Current Audio AMP-1270 from humming when receiver/source is off?
- K
  kimgreenAug 28, 2025
  To address hum from your Current Audio Amplifier when the receiver/source is off: * Turn down the rear Level or Global level. * Insert an in-line ground isolator if the cable TV ground differs from the earth ground. * Address any ground loop issues by commoning all grounds and isolating the AC ground.
D
David GonzalezAug 30, 2025
Why is there no audio from speakers connected to Current Audio Amplifier?
- V
  Victoria GibbsAug 30, 2025
  If you're not getting any audio from the speakers connected to your Current Audio Amplifier, check the speaker wiring at both the amplifier and the speakers to ensure proper connections.
J
jacksonmichaelSep 1, 2025
What to do if the 12 Volt Trigger is not working on Current Audio AMP-1270 Amplifier?
- J
  Joseph RyanSep 2, 2025
  If the 12 Volt Trigger on your Current Audio Amplifier isn't working, make sure the power switch on the front panel is in standby mode, indicated by a RED light. It should be BLUE when triggered.
J
johnsonwilliamSep 4, 2025
Why is there no sound from my Current Audio Amplifier?
- J
  Jordan KelleySep 4, 2025
  If your Current Audio Amplifier isn't producing sound, several factors could be at play. Ensure the unit is plugged into a working, unswitched AC power outlet. Verify all audio cables are securely connected to the correct inputs, and consider replacing them if necessary. If you're using a matrix switcher, confirm it's programmed to send a signal to your input, and check the audio format on your DVD player. Also, make sure the Master Power switch on the rear of the amplifier is set to 'ON' and that the front power switch is toggled to show a BLUE light. Check if a 12 Volt Trigger is applied.
C
crystal13Sep 6, 2025
What to do if my Current Audio AMP-1270 has a hum or buzz?
- J
  Joshua WilsonSep 6, 2025
  If your Current Audio Amplifier is producing a hum or buzz, try these steps: Ensure RCA cables are fully pushed in; replace them if needed. Check the grounding with a plug tester, try reversing the cord, or use a 2-prong adapter. If prewired cables run near AC wires, insert an isolation transformer in-line with the RCA jacks.
L
Lauren WilliamsSep 9, 2025
How to fix Current Audio AMP-1270 Amplifier when no audio from one or more channels?
- L
  Lori LopezSep 9, 2025
  If you're experiencing a lack of audio from one or more channels on your Current Audio Amplifier, start by checking the source cable and its output. Ensure the Normal/Line-In switch is in the correct position. Verify the Bridge/Normal switch position, referring to the manual for proper settings. Inspect the speaker connections for any loose wires or shorts, as a short can cause that zone to shut down both channels.
C
Chris VaughanSep 13, 2025
Why does my Current Audio Amplifier hum when the receiver/source is off?
- Z
  zflynnSep 13, 2025
  If your Current Audio Amplifier hums when the receiver or source is off, the level might be set too high. Try turning down the rear Level or Global level. The issue might also be due to the Cable TV ground not being the same as the earth ground; in this case, insert an in-line ground isolator. It could also be a ground loop, try to common all grounds, isolate AC ground.