Curtis D1000GT - Program Menu Options; Pre-Infusion Setting; Cold Brew Lock; Master Reset

3
Brew Count Total
Press  to Select, Shows total gallons and total brew cycles on the unit. Cannot be reset.
Cold Brew Lock . . . (Factory set to 5º)
Press toselect,<>toselectdesiredsetting(CBL5,15orOFF), to set.
TheColdBrewLockfeatureallowsthebrewertobrewatthreedifferenttemperaturelevelsfromtheactualsetpoint.Therstsettingis
within5degreesofsetpoint,nextiswithin15degreesofsetpoint,OFFiswithin30degreesofsetpointfortheReadytoBrewmes-
sage,howeveritwillbrewatanytemperature.
Master Reset
Press todisplayAreYouSure?
Then<forYes,>forNo.
Brewerfactorydefaultsarethenreset.
Service Call (Phone number Factory set to 1-800-000-0000)
Press todisplaynumberandchangenumberor<tomoveplaceandEXtoexitwhencompleteThisnumberwillbedisplayeddur-
ingaHeatingsystemSENSORERRORorduringaWATERERROR.
Access Code (Factory set to 1-2-3-4)
Press todisplaynumberandchangenumber,(thenumbercanbechange1to4)or<tomoveplaceandextoexitwhencomplete.
Banner Name (Factory set to Curtis)
Press todisplaycurrentbanner.Press<>tomoveplaceandEXtoexitwhencomplete.Thisfeatureallowsupto14lettersto
beprogrammedforcompanynameorregionalname.ProgrammingallblanksdisablesBannerName.Oncethebannerhasbeen
programmed,thewordswillbedisplayedduringnormaloperation,abovethewordsReadytoBrew.
P-Maintenance (Factory set to OFF)
Press toSelect,SetgallonsbrewedtoindicateP-Maintenance.Press<>toadjustfromOffto3000gallons.Presstoexit.
Beeper On/Off (Factory set to ON)
Press todisplayONorOFF.Pressingeither<>togglesbetweenonandoff.to set.
Pulse Brew (Factory set to OFF)
Press  to select. DisplaywillnowshowSelectButton.SelectdesiredBrewbuttontoprogram.Thenextscreenwillpromptyouto
press < >toselectOFForoneoffourpulsepatterns(AtoE).
GuidelinesforPulseBrew:
Thisfeatureallowstuningofthecoffeeavor.ThepotlevelshouldalwaysbesetrstwiththisoptionOFF.Dependingonyourgrind
proleandwaterconditions,thevePulseBrewoptionshelp“tune”orchangethecoffeeavor.FilterPacktypecoffeestypically
extractbetterwiththeAandBpulsesetting.DecaffeinatedcoffeestypicallyextractbetterwiththeBpulsesetting.High-Yieldcoffees
typicallyextractbetterwiththeCpulsesetting.Ofcourse,anyoftheA,BorCsettingsmaybeusedtosuityourtasteprole.Thereare
twoadditionalsettings(DandE)thatallowyoutomanuallysettheONTIMEpulsesandOFFTIME.
IfPulseBrewisselected(ON),ColdBrewLockissettoDelta1within5ºFofsetpoint.ColdBrewLockandPre-infusiondisappears
fromthelistofprogramselections.WhenPulseBrewisON,Pre-Infusiondisappearsfromthelistofprogramselections.
Display Brew Time (Factory set to ON)
Press todisplayONorOFF.Pressingeither<or>togglesbetweenonandoff.toset.Whenon,theDisplayBrewTimefeature
allows you to see the remaining time in the brew cycle counting down.
Drip-Out Mode (Factory set to 2 min)
Press toselect.Press>toincreasetime(toamaximumof5minutes)or<todecreasethetimeandturnOFF.Timecountsupin5
second increments. Press  to set.
Exit
Press toselect,exitsprogrammodeandreturnsunittooperation.Pressing>returnsyoutoBrewByVolume.
MasterReset
Service Call
Access Code
BannerName
P-Maintenance
BrewCountTotal
ColdBrewLock
BeeperOn/Off
PulseBrew
On/Off
Exit
Drip-Out
Mode
DisplayBrew
Time