To Next PageTo Next PageWhat to do if my CyberPower OL1000RTXL2U shows 'Load Over XXX%'?
If your CyberPower UPS displays 'Load Over XXX%', your equipment requires more power than the setting in the Power Management Software (PowerPanel® Business) allows. You can shut off non-essential equipment or increase the level in the Power Management Software.
What to do if my CyberPower UPS displays 'Wiring Fault'?
If your CyberPower UPS displays a 'Wiring Fault' (not applicable on OL3000RTXL2UHV), it could be due to several reasons: - Line and neutral wires are reversed: Exchange the line and neutral wires. - Missing ground wire: Connect the ground wire. - No ground wire: Disable the Wiring Fault alarm on the LCD panel.
What to do if CyberPower OL1000RTXL2U UPS says 'Battery Low'?
If your CyberPower UPS indicates 'Battery Low,' it means the UPS is running on battery power and will shut down soon because of extremely low battery voltage. The UPS will automatically restart when acceptable utility power returns.
How to fix a CyberPower OL1000RTXL2U UPS overload?
If your CyberPower UPS is showing an O/P Overload, it means your equipment requires more power than the UPS can provide. To solve this, shut off non-essential equipment. If this resolves the issue, the UPS will return to normal operation.
What to do if my CyberPower UPS is in battery mode?
If your CyberPower UPS is operating on battery power, immediately save your data and perform a controlled shutdown of your equipment.
What happens when my CyberPower OL1000RTXL2U displays 'Battery Low'?
When your CyberPower UPS displays 'Battery Low', it means the UPS is running on battery power and will shut down soon due to extremely low battery voltage. The UPS will restart automatically when acceptable utility power returns.
Why is my CyberPower OL1000RTXL2U UPS showing Battery Failure?
If your CyberPower UPS has failed a Battery Test, check the battery connector and battery breaker. If the issue persists, contact technical support to replace the battery.
What to do if my CyberPower OL1000RTXL2U battery is low?
If your CyberPower UPS is operating on battery power and the battery is low, it will be shutting down soon due to extremely low battery voltage. The UPS will restart automatically when acceptable utility power returns.
What to do if my CyberPower OL1000RTXL2U shows 'Service Battery'?
If your CyberPower UPS displays 'Service Battery', the Battery Replacement Date has reached the recommended three-year maintenance period. Perform a runtime calibration to verify battery capacity is sufficient and acceptable. If the batteries have been recently replaced, then reset the Battery Replacement Date using PowerPanel® Business Agent software, RMCARD interface (if installed) or through the LCD control panel on the UPS.
When should I replace the battery in my CyberPower UPS?
The 'Replace Battery' message on your CyberPower UPS indicates that the battery will soon need replacement due to insufficient runtime. Contact technical support to replace the battery.
General| Type | Line Interactive |
|---|---|
| Topology | Double Conversion |
| Capacity | 1000VA/900W |
| Input Voltage | 120V |
| Output Voltage | 120V |
| Output Frequency | 60Hz |
| Waveform | Sine Wave |
| Transfer Time | 4 ms |
| Number of Outlets | 8 |
| Outlets | NEMA 5-15R |
| Data Line Protection | Yes |
| Communication Ports | USB, Serial |
| Display | LCD |
| Battery Type | Sealed Lead-Acid |
| Form Factor | Rackmount |
| Operating Temperature | 32°F to 104°F |
Key safety instructions and warnings for installation and operation of the UPS unit.
List of all items included in the UPS system package.
Steps to install the UPS into a 4-post rack, including rail and ear attachment.
Instructions for installing the UPS into a 2-post rack, including ears and securing.
Guide for setting up the UPS in a vertical or tower orientation using base stands.
Visual representation of the UPS internal components and signal flow.
Overview of power button, status indicators, LCD readout, and key component functions.
Guide to configuring UPS settings, accessing information, and managing event logs via LCD.
Managing audible alarms and understanding graphical load/battery capacity displays.
Instructions for connecting the UPS LCD control panel for remote operation.
Guidelines for mounting the UPS LCD control panel on a wall.
Recommendations for storing the UPS and maintaining battery health.
Detailed steps and safety precautions for replacing UPS batteries.
Information on proper and environmentally sound disposal of UPS batteries.
Detailed technical data for UPS models, including capacity, input/output, and performance.
Specifications for surge protection, battery, operating environment, and certifications.
Solutions for common UPS warnings and faults like Overload, Battery Low, and Wiring Fault.
Guidance for battery service, calibration, and resetting the replacement date.
Diagnosing and resolving advanced faults like Charger Failure, Bus Fault, and Fan Error.
Details on the energy-saving design and environmental benefits of the UPS technology.
Information on FCC compliance, limited warranty, and contact details.
