D-Link DCS-932L User Manual

51D-Link DCS-932L User Manual
Section 6 - Troubleshooting
Yes, you can access your camera over the Internet through the following URL after successfully installing your camera through the Camera Installation
Wizard:
http://[mydlink No.].mydlink.com
For example, if your camera’s mydlink No. was 12345678, you would be able to access your camera remotely by opening your web browser and
going to http://12345678.mydlink.com
This URL will open a webpage where you will be asked to log in by entering your camera’s password. After entering your password, your camera’s
Live View window will open, and you will be able to congure your camera as well.
4. Why does the LED not light up?
The power supply might be faulty. Conrm that you are using the provided DC 5V power supply for this network camera. Verify that the power
supply is correctly connected. If the camera is functioning normally, the LED may have been disabled. See page 37 for information about how to
enable the LED.
5. Why is the camera’s network connection unreliable?
There might be a problem with the network cable. To conrm that the cables are working, PING the address of a known device on the network. If
the cabling is OK and your network is reachable, you should receive a reply similar to the following (…bytes = 32 time = 2 ms).
Another possible problem may be that the network device such as a hub or switch utilized by the Network Camera is not functioning properly.
Please conrm the power for the devices are well connected and functioning properly.
6. Why does the Network Camera work locally but not remotely?
This might be caused by the rewall protection. Check the Internet rewall with your system administrator. The rewall may need to have some
settings changed in order for the Network Camera to be accessible outside your local LAN. For more information, please refer to the section about
installing your camera behind a router.
Make sure that the Network Camera isn’t conicting with any Web server you may have running on your network.
The default router setting might be a possible reason. Check that the conguration of the router settings allow the Network Camera to be accessed
outside your local LAN.

D-Link DCS-932L Specifications

General

Maximum resolution	640 x 480 pixels
Supported video modes	-
Video formats supported	M-JPEG
Supported graphics resolutions	640 x 480 (VGA)
White balance	Auto
Minimum illumination	1 lx
Sensor type	CMOS
Optical sensor size	1/5 \
Digital zoom	4 x
Optical zoom	- x
Security algorithms	WEP, WPA, WPA2
Ethernet LAN	Yes
Cabling technology	10/100Base-T(X)
Supported network protocols	IPV4, ARP, TCP, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, FTP, HTTP, PPPoE, UPnP, LLTD
AC input voltage	100-240 V
DC output current	1.2 A
DC output voltage	+5V
AC input frequency	50 - 60 Hz
Power consumption (typical)	2 W
Certification	- FCC - B - IC - C-Tick - CE
Placement supported	Indoor
Connectivity technology	Wired & Wireless
LED type	IR
Dimensions (WxDxH)	65.8 x 65 x 126 mm
Minimum RAM	128 MB
Minimum processor	1.3 GHz
Mac operating systems supported	Mac OS X 10.5 Leopard
Cables included	LAN (RJ-45)
Built-in HDD	No
Flash memory	4 MB
Internal memory	32 MB
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	20 - 80 %
Product color	White
Ethernet LAN (RJ-45) ports	1

Weight and Dimensions

Depth	60 mm
Width	27.2 mm
Height	96 mm
Weight	76.9 g