Daikin FTXS-L Series - Page 60

EDUS091128 Installation Manual
Split Type Air Conditioners FTXS-L / FDXS-L Series 59
Preparation before Installation
rAttachment methods of metal plate electrical wiring cover
#VVCEJVJGOGVCNRNCVGGNGEVTKECNYKTKPIEQXGTCUUJQYPDGNQY
.GCPVJGOGVCNRNCVGGNGEVTKECNYKTKPIEQXGTCUUJQYPKPVJGƂIWTGCPFCVVCEJVCDQPVJGNQYGTUKFGVQVJGGNGEVTKECN
YKTKPIDQZ
#VVCEJVCDQPVJGNQYGTUKFGQHVJGOGVCNRNCVGGNGEVTKECNYKTKPIEQXGT
Tab (1)
Tab (2)
Tab (1)
2WUJKPVJGWRRGTRCTVQHVJGOGVCNRNCVGGNGEVTKECNYKTKPIEQXGTCPFCVVCEJVJGVCDU
Tab
CAUTION
r/CMGUWTGVJCVVJGUJCFGFRCTVYKNN
PQVIQKPUKFGVJGGNGEVTKECNYKTKPIDQZ
Refrigerant Piping Work
1. Flaring the pipe end
%WVVJGRKRGGPFYKVJCRKRGEWVVGT
4GOQXGDWTTUYKVJVJGEWVUWTHCEGHCEKPIFQYPYCTF
UQVJCVVJGEJKRUFQPQVGPVGTVJGRKRG
2WVVJGƃCTGPWVQPVJGRKRG
(NCTGVJGRKRG
%JGEMVJCVVJGƃCTKPIKURTQRGTN[OCFG
Set exactly at the position shown below.
A
Flaring
Die
A 0-0.020 inch (0-0.5mm)
Clutch-type
Flare tool for R410A
0.039-0.059 inch (1.0-1.5mm)
Clutch-type (Rigid-type)
0.059-0.079 inch (1.5-2.0mm)
Wing-nut type (Imperial-type)
%QPXGPVKQPCNƃCTGVQQN
(Cut exactly at
right angles.)
Remove burrs.
Check
Flare’s inner surface
OWUVDGƃCYHTGG
The pipe end must
DGGXGPN[ƃCTGFKPC
perfect circle.
Make sure that the
ƃCTGPWVKUƂVVGF
WARNING
r&QPQVWUGOKPGTCNQKNQPƃCTGFRCTV
r2TGXGPVOKPGTCNQKNHTQOIGVVKPIKPVQVJGU[UVGOCUVJKUYQWNFTGFWEGVJGNKHGVKOGQHVJGWPKVU
r0GXGTWUGRKRKPIYJKEJJCUDGGPWUGFHQTRTGXKQWUKPUVCNNCVKQPU1PN[WUGRCTVUYJKEJCTGFGNKXGTGFYKVJVJGWPKV
r0GXGTKPUVCNNCFTKGTVQVJKU4#WPKVKPQTFGTVQIWCTCPVGGKVUNKHGVKOG
r6JGFT[KPIOCVGTKCNOC[FKUUQNXGCPFFCOCIGVJGU[UVGO
r+PEQORNGVGƃCTKPIOC[ECWUGTGHTKIGTCPVICUNGCMCIG