Daikin FTXS-L Series - Page 70

EDUS091128 Installation Manual
Split Type Air Conditioners FTXS-L / FDXS-L Series 69
3. How to set the different addresses
9JGPKPFQQTWPKVUCTGKPUVCNNGFKPQPGTQQO
VJGYKTGNGUUTGOQVGEQPVTQNNGTUECPDGUGVHQT
FKHHGTGPVCFFTGUUGU
4GOQXGVJGOGVCNRNCVGGNGEVTKECNYKTKPI
EQXGT
4GHGTVQVJGWhen connecting to an HA
system
%WVVJGCFFTGUULWORGT,#QPVJGRTKPVGF
EKTEWKVDQCTF
%WVVJGCFFTGUULWORGT,#KPVJGTGOQVG
EQPVTQNNGT
ADDRESS
JA
ADDRESS
JA
EXIST 1
CUT 2
Jumper
ADDRESS:JA
EXIST 1
CUT 2
4. When connecting to an HA system
(wired remote controller, central remote controller etc.)
4GOQXGVJGHTQPVITKNNGUETGYU
4GOQXGVJGGNGEVTKECNYKTKPIDQZUETGY
4GOQXGVJGOGVCNRNCVGGNGEVTKECNYKTKPIEQXGTVCDU
#VVCEJVJGEQPPGEVKQPEQTFVQVJG5EQPPGEVQTCPFRWNNVJGJCTPGUUQWVVJTQWIJVJGPQVEJGFRCTVKPVJGƂIWTG
4GRNCEGVJGGNGEVTKECNYKTKPIEQXGTCUKVYCUCPFRWNNVJGJCTPGUUCTQWPFCUUJQYPKPVJGƂIWTG
3) Remove the metal plate
electrical wiring cover.
4) Attach the connection cord
to the S21 connector and
pull the harness out through
the notched part in the
ƂIWTG
5) Replace the electrical
wiring cover as it was,
and pull the harness
around, as shown in
VJGƂIWTG
Screw
Pull
Pull
Slide
Tab
Tab
Slide
Metal plate
electrical cover
Main body
HA connector
(S21)
HA connector
(S21)
Lay the HA cord as
UJQYPKPVJGƂIWTG
Refrigerant Piping Work
1. Flaring the pipe end
%WVVJGRKRGGPFYKVJCRKRGEWVVGT
4GOQXGDWTTUYKVJVJGEWVUWTHCEGHCEKPIFQYPYCTFUQ
VJCVVJGEJKRUFQPQVGPVGTVJGRKRG
2WVVJGƃCTGPWVQPVJGRKRG
(NCTGVJGRKRG
%JGEMVJCVVJGƃCTKPIKURTQRGTN[OCFG
Set exactly at the position shown below.
A
Flaring
Die
A 0-0.020 inch (0-0.5mm)
Clutch-type
Flare tool for R410A
0.039-0.059 inch (1.0-1.5mm)
Clutch-type (Rigid-type)
0.059-0.079 inch (1.5-2.0mm)
Wing-nut type (Imperial-type)
%QPXGPVKQPCNƃCTGVQQN
(Cut exactly at
right angles.)
Remove burrs.
Check
Flare’s inner surface
OWUVDGƃCYHTGG
The pipe end must
DGGXGPN[ƃCTGFKPC
perfect circle.
Make sure that the
ƃCTGPWVKUƂVVGF
WARNING
r&QPQVWUGOKPGTCNQKNQPƃCTGFRCTV
r2TGXGPVOKPGTCNQKNHTQOIGVVKPIKPVQVJGU[UVGOCUVJKUYQWNFTGFWEGVJGNKHGVKOGQHVJGWPKVU
r0GXGTWUGRKRKPIYJKEJJCUDGGPWUGFHQTRTGXKQWUKPUVCNNCVKQPU1PN[WUGRCTVUYJKEJCTGFGNKXGTGFYKVJVJGWPKV
r0GXGTKPUVCNNCFTKGTVQVJKU4#WPKVKPQTFGTVQIWCTCPVGGKVUNKHGVKOG
r6JGFT[KPIOCVGTKCNOC[FKUUQNXGCPFFCOCIGVJGU[UVGO
r+PEQORNGVGƃCTKPIOC[ECWUGTGHTKIGTCPVICUNGCMCIG