OM 1280-2 • MICROTECH UNIT CONTROLLER 68 www.DaikinApplied.com
Menu Name
(Menu Index)
Minimum Password to Read
(None, User, Manager, Technician)
Minimum Password to Write
(None, User, Manager, Technician)
“RO” if Read Only
Help Text
Set|Compressor
CmpMtrVlvTm: N T Motorize valve delay.
CmpMnOnTm: N T Compressor minimum on time.
N T
ClOATLckSpt: N T
CmpHtOATLck: N T
CmpHtEWTLck: N T
N T
RevVlvTmr: T RO Rev vlv chgs this long after comp start.
Set|Timers
EWFlwTmSpt: N M Flow time before hydro ht/cl available.
MnStgTmSpt: N M Minimum state transition time.
ClStgTmSpt: N M Min time before clg stg chg can occur.
HtStgTmSpt: N M Min time before htg stg chg can occur.
NgtPrgTm: N M Night purge state time.
Set|Dehumid
SpcRHSpt: N M Space relative humidity setpoint.
T M
KeyDehumEn: N M
DehumType: T T Active adds reheat.
DehumStgDn: T T
PassDehumFBPD: T T F&B damper max for passive dehum.
NetDehumEn: N RO
SpcRHEn: T T Space humidity sensor enable.
OutRHEn: T T Outdoor humidity sensor enable.
EnthSel: T T Select outdoor enthalpy calc strategy.
DehumFanSpt: T T
DehumLTmpSpt: T T
Set|DAT
DATClSpt: N M DAT cooling setpt when not reset.
DATHtSpt: N M DAT heating setpt when not reset.
DAEconLL: N T DAT Clg LL during non-comp cooling.
DAMechLL: N T Discharge air mech low limit setpt.
RehtLLStTime: T T Reheat to ReheatLL time.
DAHiLim: N T Discharge air high limit.
DATRstClSel: N T Source of DAT Clg reset control.
MnDATClSpt: T T Min input to DAT clg reset calc.
MxDATClSpt: T T Max input to DAT clg reset calc.
MnDATClCntSpt: T T Min DAT clg reset setpt.
MxDATClCntSpt: T T Max DAT clg reset setpt.
DATRstHtSel: N T Source of DAT Htg reset control.
MnDATHtSpt: T T Min input to DAT htg reset calc.
MxDATHtSpt: T T Max input to DAT htg reset calc.
MnDATHtCntSpt: T T Min DAT htg reset setpt.
MxDATHtCntSpt: T T Max DAT htg reset setpt.
DATClDb: T T DAT cooling deadband.
DATHtDb: T T DAT heating deadband.
RstReHtSel: T T DAT reset reheat select.
MnDATReHtSpt: T T Min input to DAT reheat reset calc.
MxDATReHtSpt: T T Max input to DAT reheat reset calc.
MnDATReHtCntSpt: T T Min DAT reheat reset setpt.
MxDATReHtCntSpt: T T Max DAT reheat reset setpt.
Set|ElectricHeat
ElHtPropGn: N T Electric heating proportional gain.
ElHtIntgGn: N T Electric heating integral gain.
ElHtStgTmSpt: T T Min time elect ht stg chg can occur.
MnElHtFanOnTm: T T Min fan on after leaving elect heat.
SupElHtSel: N M Allow elect heat to supplement primary.
Set|OutdoorDamper
OADMnPos: N M Min OAD for CO2 and fan at high speed.”
OADMnPosMdSpd: N M Min OAD when space fan at medium speed.”
OADMnPosLwSpd: N M Min OAD when space fan at low speed.”
SpcCO2Lim: N M Space CO2 setpoint.
EconOASpt: N M Economizer outdoor air setpoint.
T T
EconEnthSpt: N M Economizer enthalpy setpoint.
T T
OAMxPos: N T Maximum Outdoor Air damper position.
OALockEn: N M OA damper low temperature lockout.
OALockSpt: N T OA damper low temp lockout setpoint.
OATSpt: N M Economizer OAT setpoint.
EconEn: N M Keypad economizer enable.
To Next Page
Loading...
