Daikin Navigator WWV - Unit Test Mode Set Points; Administration and Service Support Settings

29
IOM 1264-4
WWW.DAIKINAPPLIED.COM
OPERATION
Table 19: Unit Test Mode Set Points
Description Default Range
Test Unit Alarm Output O󰀨 O󰀨, On
Test Evaporator Pump Output 1 O󰀨 O󰀨, On
Test Evaporator Pump Output 2 O󰀨 O󰀨, On
Test Condenser Pump Output 1 O󰀨 O󰀨, On
Test Condenser Pump Output 2 O󰀨 O󰀨, On
Test Cooling Tower Fan 1
Output
O󰀨 O󰀨, On
Test Cooling Tower Fan 2
Output
O󰀨 O󰀨, On
Test Cooling Tower VFD Speed 0.0% 0.0% to 100.0%
Test Cooling Tower Bypass
Valve Position
0.0% 0.0% to 100.0%
NOTE: Unit test mode set points can be changed only when
the unit mode is Test. When the unit mode is no longer
Test, all unit test mode set points will be changed back
to the ‘o󰀨’ values.
Table 20: Administration and Service Support
Description Default Range
Unit G.O. Number “Enter Data”
Alphanumeric string of up to
16 characters
Unit Serial Number “Enter Data”
Alphanumeric string of up to
20 characters
Next Maintenance
Month
January January through December
Next Maintenance
Year
2017 2009 - 2200
Service Support
Reference
999-999-9999 Any 10 digit phone number
Controller Time
From Controller
Timeclock
00:00:00 to 23:59:59
Controller Date
From Controller
Timeclock
1/1/2000 to 12/31/2050
UTC Di󰀨erence -60 minutes -3276 to 32767 minutes
Daylight Savings
Time Enable
Yes No, Yes
Daylight Savings
Time Start Month
March January through December
Daylight Savings
Time Start Week
2nd Week 1st through 5th Week
Daylight Savings
Time End Month
November January through December
Daylight Savings
Time End Week
1st Week 1st through 5th Week
Operator Password
Disable
O󰀨 O󰀨, On
Apply Changes No No, Yes
Active Alarm Clear No No, Yes
Alarm Log Clear No No, Yes
Log Export to SD
Card
No No, Yes
Load Files from SD
Card
No No, Yes
Save Settings to
SD Card
No No, Yes
Restore Settings
from SD Card
No No, Yes
Description Default Range
Restore Default
Settings
No No, Yes
Display Units English English, Metric
Saving and Restoring Settings
When the ‘Save Settings To SD Card’ setting is set to ‘Yes’, all
the setting values should be saved into a le on the SD card.
This operation requires that there is an SD Card in the slot on
the controller and it is not write protected. When the operation
completes, the setting should change back to ‘No’.
This operation is dependent on functionality built into the
controller rmware so only some aspects of the behavior can be
changed via the controller software. The settings will be saved
on the SD Card in two les: PARAM.BIN and PARAM.UCF. Both
les are standalone and contain all the setting values.
When the ‘Restore Settings From SD Card’ setting is set to
‘Yes’, the setting values should be changed to those found in the
PARAM.BIN or PARAM.UCF le on the SD card. If both les are
on the SD card, the controller will use the PARAM.BIN le. After
the setting values are loaded from the SD card, the controller
should automatically reboot in order to apply all the setting
changes.
When the ‘Restore Defaults’ setting is set to ‘Yes’, the setting
values should all change back to the original values in the
software.