Danfoss TP5000 Si

Fig.1
TP5000 Si/TP5000 RF Si
User Instructions
Mon-Fri Sat-Sun
Fig.2
Before programming the thermostat press and release the RESET button to restart
the unit. (Fig. 1)
Setting the Clock and Day
The day and time are set in the factory and therefore it will not normally be necessary
to do this on site. Changes between summer and winter time are handled automatically
by the unit.
Accepting the Factory Pre-settings
The TP5000 Si has pre-set times already programmed in, which often suit most people
(see table below).
Note: If set up for 4 events per day, events 3 & 4 are skipped. If set up for 2 events per
day, events 2, 3, 4 & 5 are skipped and the events are re-numbered.
To adjust the factory pre-settings & set your own time and temperature
programmes
For Days 1-5 (weekdays)
a) Press PROG (Fig. 2) until the 1
st
pre-set time and temperature (Event 1 Days 1,2,3,4,5)
(Fig. 3).
b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min
increments).
c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE.
d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6).
e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6.
For Days 6-7 (weekends)
Press • PROG (Fig. 2) to show 1
st
pre-set time and temperature (Event 1 Days 6-7)
(Fig. 7).
Repeat steps b, c and d above to programme time and temperature events for •
the weekend.
Returning to RUN mode
Press PROG (Fig. 2) – the colon in the LCD display will start to flash (Fig. 8).
Fig.5
Fig.4
Fig.6
Fig.7
Fig.8
Event Time Temp. °C
1 06:30 20
2 08:30 15
3 11:30 20
4 13:30 15
5 16:30 21
6 22:30 15
Event Time Temp. °C
1 07:30 20
2 09:30 20
3 11:30 20
4 13:30 20
5 16:30 20
6 22:30 15
RESET
Fig.3
Complete Shut off - Summer time
Press Λ and V together to enter thermostat mode. A frost protection symbol (snowflake in a
shield) will appear in the display . Press the down arrow ∨ once, OFF will appear in the display.
To return to automatic programming press both ∧ and ∨ together.

Danfoss TP5000 Si Specifications

General

Display	LCD
Power Supply	2 x AA batteries
Accuracy	±0.5°C
Protection Class	IP30
Mounting	Wall mounted
Type	Room Thermostat
Temperature Range	5°C to 30°C
Programming	5/2-day programming
Control Mode	On/Off
Switching Current	3A
Frost Protection	Yes (5°C)

Summary

Thermostat Programming and Setup

Setting the Clock and Day

Details on setting the thermostat's internal clock and day, including automatic DST changes.

Accepting Factory Pre-settings

Information on using the thermostat's pre-programmed time and temperature settings.

Customizing Time and Temperature Programmes

Guide to adjusting pre-set times/temps or creating user-defined schedules for weekdays and weekends.

Returning to RUN Mode

Procedure to exit programming mode and resume normal thermostat operation.

Complete Shut Off - Summer Time

Instructions for disabling heating and entering a frost protection mode for summer use.

Temporary User Overrides

Display Selection

Switching the main LCD display between time and actual room temperature.

Temporary Temperature Override

Manually setting a different temperature which reverts at the next programmed event.

Frost Protection Mode

Setting a low constant temperature for when away from home.

Battery and RF Model Operations

Battery Replacement

Procedure and warnings for replacing the thermostat's batteries.

Important RF Models Only

Essential steps for RF models including reset before commissioning.

Commissioning Instructions

Steps for tuning the RF receiver to the thermostat signal.

Service Interval Timer

Service Warning Alerts

Description of visual and audible warnings indicating upcoming boiler servicing.

Consequences of Non-Servicing

Details on system limitations and warnings if the service interval is not met.