Danfoss TP5000 - User Manual

Fig.1
Space for additional
logo if required
TP5000
User Instructions
Mon-Fri
Sat-Sun
Event Time Temp°C Event Time Temp°C
1 06.30 20 1 07.00 20
2 08.30 15 2 16.00 21
3 11.30 20 3 23.00 15
4 13.30 15 4 00.00 15
5 16.30 21 5 01.00 15
6 22.30 15 6 01.59 15
Fig.2
i2 00
1
Before programming the thermostat press the + & – AND
∧∧
∧∧
∧ and
∨∨
∨∨
∨ buttons
simultaneously to reset the unit (Fig.1)
Setting the Clock and Day
Press PROG (Fig.2) to begin programming
Use + or – buttons (Fig.3) to adjust the TIME (Fig.4)
Press PROG again (Fig.2)
Use + or – buttons (Fig.3) until correct DAY is shown (Fig.5)
(1 = Monday, 2 = Tuesday, etc)
Accepting the Factory Pre-settings
The TP5000 has pre-set times already programmed in, which often suit most
people (see Table below).
To accept these settings close the front cover and after 2 minutes the pre-
settings will automatically be accepted.
To adjust the factory pre-settings & set your own time and
temperature programmes
For Days 1-5 (weekdays)
a) Press PROG (Fig.2) 3 times to show the 1
st
pre-set time and temperature
(Event 1 Days 1,2,3,4,5) (Fig.6)
b) Use + or – buttons (Fig.3) to adjust the TIME (press and hold to change in
10 min increments)
c) Use
∧∧
∧∧
∧ or
∨∨
∨∨
∨
buttons (Fig.7) to adjust the TEMPERATURE
d) Press PROG (Fig.2) to move to next preset time & temp (Event 2) (Fig.8)
e) Repeat steps b, c & d for programming Events 3, 4 5 & 6
For Days 6-7 (weekends)
● Press PROG (Fig.2) to show 1
st
pre-set time and temperature (Event 1
Days 6-7) (Fig.9)
● Repeat steps b, c and d above to programme time and temperature events
for the weekend
Returning to RUN mode
Press PROG (Fig.2) – the colon in the LCD display will start to flash (Fig.10)
Fig.6
Fig.7
Fig.5
Fig.3
Fig.4
Fig.8
20
1
i2 24
20
12345
1
6 30
20
67
1
7 00
15
12345
2
8 30
Fig.9
Fig.10

Danfoss TP5000 Specifications

General

Display	LCD
Temperature Range	5°C to 30°C
Control Mode	TPI (Time Proportional Integral)
Mounting	Wall-mounted
Type	Programmable Room Thermostat
Programs	7-day programmable
Power Supply	Battery powered
Battery Type	2x AA
Switching Current	3A
Accuracy	+/- 0.5°C

Summary

Setting the Clock and Day

Setting the Clock and Day

Instructions for setting the time and day on the thermostat using the PROG and +/- buttons.

Accepting the Factory Pre-settings

How to accept default programmed times and temperatures by closing the cover.

Adjusting Programmes

For Days 1-5 (weekdays)

Steps to adjust pre-set times and temperatures for weekdays (Events 1-6).

For Days 6-7 (weekends)

Steps to adjust pre-set times and temperatures for weekends (Events 1-6).

Returning to RUN Mode

Returning to RUN Mode

Exiting programming mode by pressing PROG until the LCD colon flashes.

Temporary User Overrides

Selection of time or actual room temperature

Switching between time and room temperature display using +/- buttons.

Temporary override of programmed temperature

Manually setting a temperature until the next programmed event.

Temporary use of weekend programmes

Activating weekend settings temporarily, cancelling at 2:00 AM.

Frost Protection

Setting a constant low temperature for when away from home.

Summer Time; Winter Time Clock

Summer Time; Winter Time Clock

Adjusting the clock for daylight saving time changes using +/- buttons.

Battery Replacement

Battery Replacement

Guidance on replacing batteries and preserving programming.