Danze D112000T - User Manual

Before Your Installation
Antes de Instalar
Avant líinstallation
Tools You Will Need
Herramientas Necesarias
Outils dont vous aurez besoin
Check to make sure you have the following parts indicated below:
Verifique que tenga todas las partes indicadas:
Vérifier pour vous assurer que vous possédez les pièces au bas:
Tub and Shower Faucet Rough-in Valve Assembly
Válvula interior de grifo para bañera y ducha
Ensemble de robinet de robinetterie brute pour bain et douche
SAFETY TIPS
• When using a solder alloy that has a tin content greater than 95%, you may need to
use more heat than can be supplied using MAPP or propane gas.
• Avoid heat damage: Remove cartridge and inner valve components before soldering.
CONSEJOS DE SEGURIDAD
• Si suelda con una aleación que contenga más del 95% de estaño, es posible que
necesite más intensidad de calor que el producido por MAPP o el gas propano.
• Para evitar daños durante la soldadura, antes de comenzar remueva el cartucho y los
componentes interiores de la válvula.
CONSEILS DE SÉCURITÉ
• L’usage d’un alliage de soudure contenant plus de 95 % d’étain peut nécessiter plus
de chaleur que peut en produire le MAPP ou le gaz propane.
• Éviter les dommages causés par la chaleur : enlever la cartouche et les composants
internes du robinet avant de souder.
Need Help? Please call our toll-free Customer service line at 1-888-328-2383 or WWW.DANZE.COM for additional assistance or service.
Requiere asistencia? Favor llamar a nuestro servicio a clientes sin costo al 1-888-328-2383 o WWW.DANZE.COM para asistencia adicional o servicio.
Besoin d’aide? Veuillez communiquer avec notre service à la clientèle au numéro sans frais 1-888-328-2383 ou WWW.DANZE.COM pour obtenir du
service ou de l’aide additionnels.
Hacksaw
Sierra para metales
Scie à métaux
Strapping
Sujeción
Bande de fixation
Phillips screwdriver
Destornillador cruciforme
Tournevis Phillips
Adjustable wrench
Llave ajustable
Clé à molette
Pipe tape
Cinta selladora para rosca
Ruban pour tuyau
Safety glasses
Lunettes de sécurité
Gafas de seguridad
Torch
Chalumeau
Soldador
D112000T
Shown /Mostrado / Illustré
D113000T
Shown /Mostrado / Illustré
D115000T
Shown /Mostrado / Illustré
Pub No. IM-T&S PBV/03-16

Summary

Installation Preparation

Safety Tips

Crucial safety advice for soldering, heat damage, and material handling.

Tools You Will Need

List of essential tools for proper installation of the faucet assembly.

Faucet Installation Procedures

Initial Setup and Notes

Instructions for shutting off water, inlet port details, and general installation notes.

Standard Valve Position

Positioning the valve body correctly relative to the finished wall surface.

Connect Water Supply Piping

Connecting threaded or soldered copper water supply tubes to the valve assembly.

Maintenance

Care and Cleaning

Recommendations for cleaning and avoiding damage to the faucet finish.

Shower Only Installation

Install Top Port Piping and Bottom Plug

Piping the top port and soldering the plug to the bottom port for shower-only setup.

Tub Filler Installation

Install Bottom Port Piping and Top Plug

Piping the bottom port and soldering the plug to the top port for tub filler setup.

Tub and Shower Faucet Installation

Connect Shower and Tub Filler Piping

Connecting piping to the top port for shower and bottom port for tub filler.

Tub Spout Stub-out Length

Measuring and installing the correct pipe stub-out length for the tub spout.

Thin Wall Construction

Hole Saw Cutting

Cutting the correct diameter hole for valve installation in thin wall construction.

Valve Assembly and Stem Positioning

Attach Collar to Plaster Guard

Securing the valve behind the wall using the collar and plaster guard.

Escutcheon Installation

Preparing and installing the escutcheon plate.

Valve Stem Positioning

Setting the valve stem correctly for standard or back-to-back installations.

Temperature Limiting Device Adjustment

Device Removal and Stem Rotation

Removing components and rotating the valve stem to adjust temperature.

Replace Cam and Nut

Reassembling the temperature limiting device components after adjustment.

Cartridge Installation

Re-install Cartridge into Valve Body

Aligning and inserting the cartridge into the valve body, verifying seals.

Verify Cartridge Seals

Ensuring the cartridge seals are correctly positioned before installation.

Cartridge Locking and Base Nut

Seat Cartridge and Tighten Locking Nut

Ensuring the cartridge is seated and tightening the cartridge locking nut to specified torque.

Hand Tighten Base Nut

Hand-tightening the base nut to the sleeve to complete cartridge installation.

Danze D112000T Specifications

General

Product Type	Faucet
Flow Rate	1.2 GPM
Finish	Chrome
Material	Brass
Number of Handles	1
Handle Style	Lever
Valve Type	Ceramic Disc
Installation Type	Single Hole
Valve Included	Yes
ADA Compliant	Yes
Warranty	Limited Lifetime