Danze FP414000 User Manual

FP414000
Tools needed:
Outils requis :
Herramientas necesarias:
Adjustable wrench
Clé réglable
Llave ajustable
Plumbers tape
Mastic d’étanchéité
Cinta de plomería
Screwdriver
Tournevis
Destornillador
Allen wrench
Clé Allen
Llave Allen
Safety goggles
Lunettes protectrices
Gafas de seguridad
Safety Tips
• When installing flexible hose, there should be no torsion or deformation; DO NOT fold into V or L
shape; DO NOT use if there are any cracks or deformations.
• The fittings should be installed by a licensed plumber of the State.
• Cover your drain to avoid losing parts.
Conseils de sécurité
• Lorsque vous installez le tuyau flexible, il ne doit exister aucune torsion ou déformation;
NE le pliez PAS en V ou L; NE L’UTILISEZ PAS s’il existe des fissures ou déformations.
• Les raccords doivent être installés par un plombier accrédité par l’État.
• Recouvrez le drain pour éviter de perdre des pièces.
Consejos de Seguridad
• Al instalar la manguera flexible, esta no debe doblarse o torcerse; NO doblar en forma de V o L;
NO usar si está agrietada o deformada.
• Estos acoplamientos deben ser instalados por un plomero con licencia del Estado.
• Cubre el drenaje para evitar que se pierdan piezas.
1
Pull-Out Kitchen Faucet
Robinet d’évier avec arroseur rétractable
Grifo de cocina con rociador retráctil
Need Help? Please call our toll-free Technical Support line at 1-800-487-8372 for additional assistance or service./
Besoin d’aide? Veuillez communiquer avec notre ligne de soutien technique sans frais à 1-800-487-8372 pour obtenir du service
ou de l’aide additionnels./¿Necesitas Ayuda? Favor de llamar a nuestro servicio de soporte técnico sin costo al 1-800-487-8372
para asistencia adicional o servicio.

Danze FP414000 Specifications

General

Brand	Danze
Model	FP414000
Category	Plumbing Product
Language	English

Summary

Tools Needed

Safety Tips

Maintenance

Important Information

Includes

Faucet Installation

Step 1: Flush Water Lines

Turn on water and flush water supply lines into a bucket to remove debris.

Step 2: Turn Off Water and Remove Nut

Turn off water supply and remove the lock nut before proceeding.

Step 3a: Without Deck Plate Installation

Instructions for installing the faucet without a decorative deck plate.

Step 3b: With Deck Plate Installation

Instructions for installing the faucet with a decorative deck plate.

Step 4: Unscrew Screws on Lock Nut

Loosen the screws on the lock nut until they are flush with its surface.

Step 5: Slide Washers and Secure Shank

Attach rubber and metal washers to the shank and secure with the lock nut.

Step 6: Connect Water Supply Lines

Connect water supply lines and tighten nuts using two wrenches.

Step 7: Remove Discharge Tube Cap

Remove the protective cap from the discharge tube.

Step 8: Attach Quick Connector

Connect the quick connector to the discharge tube and ensure it is secure.

Step 9: Attach Hose Weight

Attach the rubber weight to the lowest point of the hose on the spout side.

Step 10: Remove Spray Head

Remove the spray head and hold the hose to prevent retraction.

Step 11: Flush Faucet

Turn on water to flush the faucet and check for leaks.

Step 12: Replace Spray Head

Turn off the faucet and replace the spray head.

Quick Connector Removal

Parts Diagram

Troubleshooting