10
LOCATIONS 080-094: AUTHORISATION LEVEL FOR CODES 1-15
Locations 080-094 can be used to control the arming and disarming authority of the individual arm/disarm codes. A code
can be given limited authority by programming a number from 1 to 15 in the corresponding location for that code. Add the
values in the table below that correspond to the desired arm/disarm characteristics, and program the sum in the appropriate
locations. The opening communicator code (location 340), and the closing communicator code (location 341) must be
enabled for opening/closing reports.
VALUE AUTHORISATION LEVEL VALUE AUTHORISATION LEVEL
0 NO AUTHORISATION LEVEL
(USED FOR AUXILIARY OUTPUT)
9 REGULAR ARM/DISARM CODE
OPEN/CLOSE REPORTS BY USER
1 REGULAR ARM/DISARM CODE 10 ARM ONLY AFTER CLOSING TIME
OPEN/CLOSE REPORTS BY USER
2 ARM ONLY AFTER CLOSING TIME
NORMALLY REGULAR CODE,
CHANGE TO ARM ONLY CODE
AFTER THE CLOSING TIME,
RESET AT THE OPEN TIME
12 ARM ONLY CODE
OPEN/CLOSE REPORTS BY USER
4 ARM ONLY CODE
LOCATION 095: DIAL ATTEMPTS FOR PHONE #1
Location 095 is used to enter the number of dial attempts (1 to 15 attempts) the communicator will try for phone number
one before ending the notification process. Factory default is "6" and the communicator will make 2 attempts to the first
number, and then 2 attempts to the second number alternating until the “6" attempts in total are made. If no second number
is programmed all “6" attempts are made to the first number. If the factory default is modified in location 146, this dial
sequence can be altered, refer location 146.
LOCATION 096: DIAL ATTEMPTS FOR PHONE #2
Location 096 is used to enter the number of dial attempts (1 to 15 attempts) the communicator will try for phone number
two before ending the notification process. NOTE: Dial Attempts for Phone 2# will only be valid if SPLIT or DUAL
REPORTING is enabled in location 146.
LOCATIONS 097-112: PRIMARY PHONE NUMBER
Phone # 1 is programmed in successive locations beginning with location 097. Delays of four seconds can be programmed
at any point in the phone number by programming a "13" in the appropriate location. If tone dialling is desired, program a
"15" in the location where tone dialling should begin. If a "¬" or "#" are required in your phone number then a "11" = "¬"
and "12" = "#". If the entire number should be tone dialling, program a "15" in location 097. Factory default is "14" in each
location and the phone number is not enabled. When using split or dual reporting, phone #1 always takes priority over
phone #2. A "14" indicates the end of the phone number. Example: If phone number 02 is to be 7244211, and must be
touch tone dialling, phone number 02 would be programmed as
[15][¬][#][0][¬][#][2][¬][#][7][¬][#][2][¬][#][4][¬][#][4][¬][#][2][¬][#][1][¬] [#][1][¬] [#][14][¬][#]. The "15" selects touch tone
dialling, and the "14" ends the phone number.
LOCATIONS 113-117: PRIMARY ACCOUNT CODE
The account code sent when phone #1 is dialled is programmed in locations 113-117. If the account code is three digits
long, use locations 113-114-115, and program a "0" in locations 116 and 117. If the account code is four digits long,
program a "0" in location 117. If a zero "0" is part of an account code, it should be programmed as a "10". Program a "0"
to indicate the end of the account code. To make this account code the account code for "Partition One", see location 146.
Example: Account number of 2090 would be entered as [2][¬][#] [10][¬][#] [9][¬][#] [10][¬][#] [0][¬][#] (starting at location
113). Account code of 209 for low speed would be entered as [2][¬][#] [10][¬][#] [9][¬][#] [0][¬][#] (starting at location 113).
To Next Page
Loading...