How to troubleshoot a Datalogic Scanner that does nothing when the scan button is pressed?
If nothing happens when you press the scan button on your Datalogic Scanner, check the following: * Ensure the scanner is receiving power. Check the system power and make sure the power supply is properly connected. * Verify that all cable connections, including interface and power cables, are securely plugged in.
What to do if my Datalogic Scanner LED is on, but the bar code does not decode?
If the LED on your Datalogic Scanner lights up but the bar code isn't decoding, here's what you can check: * Make sure the scanner is set up to read the specific type of bar code you're scanning. * Examine the bar code label to be sure it's clear and not damaged. You can try scanning a different bar code to see if that works. * Adjust the distance between the scanner and the bar code. Try moving the scanner closer or farther away from the bar code.
What to do if Datalogic Heron HD3130 Barcode Reader LED is on but barcode does not decode?
If the Datalogic Barcode Reader's LED is on, but it doesn't decode the barcode, there might be a few reasons. First, the imager might not be programmed for the correct barcode type, so ensure it is properly programmed. Second, the barcode label might be unreadable; check if it's defaced and try scanning another barcode. Finally, the distance between the imager and the barcode could be incorrect; try moving the imager closer to or further from the barcode.
How to troubleshoot Datalogic Heron HD3130 when nothing happens when the scan button is pulled?
If nothing happens when you pull the scan button on your Datalogic Barcode Reader, it could be due to a couple of reasons. First, check the system power and ensure the power supply is connected. Second, make sure all cable connections are secure, as loose interface or power cables could be the cause.
What to do if my Datalogic Heron HD3130 LED is on but not decoding?
If the LED is illuminated, but the bar code isn't decoding, there could be several reasons: * The barcode reader may not be programmed to read that specific type of barcode. * The barcode label might be damaged or unreadable. Try scanning a different barcode to see if that works. * The distance between the barcode reader and the barcode itself may be incorrect. Try moving the reader closer to or further away from the barcode.
Why is my Datalogic Heron HD3130 not working when I pull the scan button?
If nothing happens when you pull the scan button on your Datalogic Barcode Reader, it could be due to the following reasons: * The imager may not be getting power. Check the system power and ensure the power supply is properly connected. * The interface or power cables might be loose. Ensure all cable connections are secure.
Why is my Datalogic Scanner decoding but not transmitting to the host?
If your Datalogic Scanner decodes the bar code but doesn't transmit the data to the host, the scanner may not be programmed for the correct host type. Scan the appropriate host type barcode to resolve this.
Why is the barcode decoded but not transmitted to the host by Datalogic Heron HD3130 Barcode Reader?
If your Datalogic Barcode Reader decodes the barcode but doesn't transmit it to the host, the imager might not be programmed for the correct host type. Scan the appropriate host type barcode to resolve this.
What to do if the LED is on but the Datalogic Laboratory Equipment barcode does not decode?
If the LED is on but your Datalogic Laboratory Equipment isn't decoding the barcode, there could be a few reasons: * The imager might not be programmed for the correct barcode type. Make sure it's set to read the specific type of barcode you're scanning. * The barcode label might be damaged or unreadable. Inspect the label for any defects. You could also try scanning a different barcode. * The distance between the imager and the barcode could be off. Try moving the imager closer to or further away from the barcode to see if that helps.
Why nothing happens when I pull the scan button on my Datalogic Laboratory Equipment?
If nothing happens when you pull the scan button on your Datalogic Laboratory Equipment, it could be due to: * **Power Issues:** Check that the system has power and ensure the power supply is properly connected. * **Loose Cables:** Make sure all cable connections are securely attached.
General| Type | Handheld bar code reader |
|---|---|
| Sensor type | CCD |
| Scanner type | 1D |
| Read rate (max) | 270 reads/s |
| Optical sensor resolution | 2500 pixels |
| Linear (1D) barcodes supported | GS1-128 (UCC/EAN-128) |
| 2D (matrix & stacked) barcodes supported | - |
| Standard interfaces | RS-232, USB, Keyboard wedge |
| Connectivity technology | Wired |
| Product color | White |
| LED indicators | Yes |
| International Protection (IP) code | IP40 |
| Sustainability certificates | RoHS |
| Power consumption | 300 mA |
| Storage temperature (T-T) | -20 - 70 °C |
| Operating temperature (T-T) | 0 - 50 °C |
| Operating relative humidity (H-H) | 5 - 90 % |
| Cables included | USB |
| Harmonized System (HS) code | 84716070 |
Weight and Dimensions| Depth | 153 mm |
|---|---|
| Width | 152 mm |
| Height | 68 mm |
| Weight | 150 g |
To Next Page
