Dell Force10 S2410-01-10GE-24P - Page 234

234 | VLANs
www.dell.com | support.dell.com
Figure 14-198. Using the show running-config and show vlan brief Commands
Use the show vlan command, without parameters, to view the system VLAN configuration:
Figure 14-199. Example Output from show vlan Command
Note the use of the caret (^) in Figure 14-199 to indicate the native VLAN for a port.
Using the
show vlan id vlan-id command command, used here to display one VLAN comprised of a port
(first display) and then another VLAN comprised of a LAG:
Force10 #show running-config
!Current Configuration:
![excerpt showing just the vlan elements in the report]!
interface vlan 1
exit
interface vlan 2
exit
interface vlan 3
exit
Force10 #show vlan brief
VLAN Name STG MAC AgingIP Address
--------- ---------- -------- ---------------- ---------------
1 abc 01800 unassigned
2 egf 0 1800 unassigned
3 sss 0 1800 unassigned
Force10#show vlan
Codes: * - Default VLAN, G - GVRP VLANs, E - Ethernet interface, ^ - Native VLAN
Vlan Id Status Q Ports
------- --------- - --------
* 1 Inactive U E 1/0/1 ,1/0/2 ,1/0/3 ,1/0/4 ,1/0/5 ,1/0/6 ,1/0/7
1/0/8 ,1/0/9 ,1/0/10,1/0/11,1/0/12,1/0/13,1/0/14
1/0/15,1/0/16,1/0/17,1/0/18,1/0/19,1/0/20,1/0/21
1/0/22,1/0/23,1/0/24,1/0/25,1/0/26,1/0/27,1/0/28
1/0/29,1/0/30,1/0/31,1/0/32,1/0/33,1/0/34,1/0/35
1/0/36,1/0/37,1/0/38,1/0/39,1/0/40,1/0/41,1/0/42
1/0/43,1/0/44,1/0/45,1/0/46,1/0/47,1/0/48,1/0/49
1/0/50,2/0/1 ,2/0/2 ,2/0/3 ,2/0/4 ,2/0/5 ,2/0/6
2/0/7 ,2/0/8 ,2/0/9 ,2/0/10,2/0/11,2/0/12,2/0/13
2/0/14,2/0/15,2/0/16,2/0/17,2/0/18,2/0/19,2/0/20
2/0/21,2/0/22,2/0/23,2/0/24,2/0/25,2/0/26,2/0/27
2/0/28,2/0/29,2/0/30,2/0/31,2/0/32,2/0/33,2/0/34
2/0/35,2/0/36,2/0/37,2/0/38,2/0/39,2/0/40,2/0/41
2/0/42,2/0/43,2/0/44,2/0/45,2/0/46,2/0/47,2/0/48
2/0/49,2/0/50,3/0/1 ,3/0/2 ,3/0/3 ,3/0/4 ,3/0/5
3/0/6 ,3/0/7 ,3/0/8 ,3/0/9 ,3/0/10,3/0/11,3/0/12
3/0/13,3/0/14,3/0/15,3/0/16,3/0/17,3/0/18,3/0/19
3/0/20,3/0/21,3/0/22,3/0/23,3/0/24,3/0/25,3/0/26
2 Inactive T E ^1/0/3
3 Inactive!