To Next PageTo Next PageHow to prevent industrial dust problems with Delta VFD055ED43S DC Drives?
To prevent issues with industrial dust for your Delta DC Drives, install the AC motor drive in a standard cabinet and cover it with a dust cover. Regularly clean the cabinet and ventilation holes to maintain good ventilation.
How to prevent greasy dirt problems with Delta VFD055ED43S?
To address greasy dirt issues with your Delta DC Drives, install the AC motor drive in a standard cabinet to keep it away from greasy dirt. Regularly clean and remove greasy dirt to prevent damage to the drive.
How to prevent corrosion in Delta DC Drives?
To avoid corrosion problems with your Delta DC Drives, install the AC motor drive in a standard cabinet to keep it away from fluids. Regularly clean the drive to prevent corrosion.
How to prevent fiber dust problems with Delta VFD055ED43S DC Drives?
To prevent fiber dust problems with your Delta DC Drives, install the AC motor drive in a standard cabinet to keep it away from fiber dust. Make sure to clean and remove fiber dust regularly to prevent damage to the drive.
General| Frequency Range | 0-400Hz |
|---|---|
| Cooling Method | Fan Cooling |
| Enclosure Rating | IP20 |
| Control Method | V/f Control, Vector Control |
| Overload Capacity | 150% for 60 seconds |
| Protection Features | Over-voltage, Over-current, Overheat, Under-voltage, Short circuit, Ground fault, Overload |
| Operating Temperature | -10°C to 50°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 90% RH, non-condensing |
| Altitude | Below 1000m |
Specifies minimum clearances for airflow and heat dissipation to prevent drive malfunction.
Lists airflow rates and power dissipation for various models to ensure adequate cooling.
Illustrates overall system wiring, showing connections for power input, reactors, brake modules, and motor.
Presents specific wiring diagrams for drive frames (B, C&D, E) detailing terminal connections.
Provides circuit diagrams for main terminals of different frames (B, C&D, E), showing power and motor connections.
Explains terminal functions and default settings for digital signals, multi-function inputs, and analog outputs.
Lists and describes fault codes displayed on the keypad, providing causes and corrective actions for troubleshooting.
Step-by-step guide for tuning Induction Motors (IM), covering basic parameters, encoder settings, and motor auto-tuning.
Step-by-step guide for tuning Permanent Magnet Motors (PM), including motor settings and auto-tuning.
Explains parameters for fine-tuning elevator performance, such as slip compensation, system control, and delay times.
Details protection parameters such as low voltage level, phase-loss protection, over-current stall prevention, and fault output options.
Provides a regular maintenance schedule covering ambient environment, voltage checks, keypad display, and mechanical parts.
Discusses issues caused by greasy dirt, potential damages, and recommends solutions like cabinet installation and regular cleaning.
Addresses problems from fiber dust, its impact on ventilation and overheating, and suggests solutions like cabinet installation and cleaning.
Covers problems from industrial dust, its impact on overheating and circuit board damage, and recommends cabinet installation and cleaning.
Addresses common issues from incorrect wiring or poor installation, such as sparking, and recommends proper screw tightening.
Explains errors from over-usage or incorrect application of multi-function terminals, advising adherence to specifications.
Explains the STO (Safe Torque Off) function, its purpose of cutting off motor power, and describes terminal functions.
Shows the internal safety circuit diagram and terminals, illustrating how STO and SCM terminals are connected.
Lists fault codes related to the STO function, such as safe torque loss and safe torque output stops.
Discusses types of EMC noise, transmission paths, and conditions that worsen EMC problems.
Explains grounding principles, protective vs. functional grounding, and various grounding systems (TN, TT, IT).
Defines shielding, its purpose, examples, and methods to reduce EMC through shielding.
Explains electromagnetic filters for noise reduction and provides installation guidelines for external filters.
