Denon AVR-3803

[] SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in "CONNECTIONS" (see pages 6 to 13), make the various
settings described below on the monitor screen using the AVR-3803/1083'S on-screen display function.
These settings are required to set up the listening room's AV system centered around the AVR-3803/1083.
• Use the following buttons to set up the system:
• Check that the remote control unit is set to AMP mode.
16
i
SYSTEM SETUP button I
I
Press th s to d sp ay the system setup menu.
_ buttons et
Use these to move the cursors (<] and D) to th
left and dghf on the screen.
l z_and _7: Use these to move the cursors (z_ and _7) to the I
/ up and down on the screen. /
ENTER button I
Press this to switch the display.
A so use th s button to compete the setting.
• System setup items and default values (set upon shipment from the factory)
Speaker
Configuration
Surround
Speaker
Setting
Crossover
Frequency
Subw0ofelm0de
Delay %me
Channel
Level
System setup
Input the combination of speakers in your system and their
corresponding s_zes (SMALL tot regular speakers, LARGE for full
size, full range} to automatically set tile composition of the slgna_s
output from the speakers and the frequency response
Use this function when using multiple surround speaker S_o_rdSuround
combinations for more ideal surround sound Once the mode
con, b]nations of surround spea_,ers to be used for the /
dlfferent surround modes are preset, the surround
speakels are selected automatically according to the SbIround
surround mode
Set the frequency (Hz) below which the bass sound of the vadous
speakers is to be output from the subwooter
This selects the subwoofer speaker for playing deep bass signals
This parameter is for optimizing the timing with which the audio
slgna_s are produced from the speakers and subwoofer accotdin 9 to
the listening position
This adiust s the volume of the signals output from the speakers and
subwoofer for the different channels _rl order to obtain optlmum
effects
Component
in Assign
FrontSp CenterSp
Large Smal_
DOLBY/
DTS WDESCREEN
SU£ROUND
A A
Default settings
Sub Woofer
Yes
5CH/TCH
STE£EO
80 HZ
Surround Sp
A/B
Small
DSP
SIMULATION
LFE
Front L & R Center Sub Woofer
12ft(36m) _ 12 ft(36m}surr
Front L Fro t R Surround
OdB O_B OdB 0
ID DVE NONE VIDEO2 NON E' VDP W DBS
COAX1 CO#* (2 OPT1 OPT2 OPT3
VD ' _/ DBS VCR /
VIDEO1 I NOI
Video Input AUTO
Mode
Turn the audio compression on or off when down mixing Dolby OFF
Digital signals
Power AMP Surlound Back
Assignment
Zone2 Variable
vol Level
Set the audio delay to delay tlme the sound and synchlonize _t with O ms
the picture
Set the Ext In Subwoofer telmklal p_ayback level Subwooter = +15 dB
Set the Auto surround mode function Auto Surround Mode = ON
This sets whether or not to display the on screen display that
appears on the monitor screen when the conttols on the remote
control unit or main unit are operated On Screen Display = ON / Mode 1
A setting to plevent flickering
Surround L & R
/0 ft (3Ore)
Surround Back Sp
Small / 2spkls
EXT IN
SBL & SBR
10 ft {3 0 ml
i_und SubwooferOdB
VCR 2 CDRfrAPE
OFF OPT5