To Next Page
B
baileytinaAug 17, 2025
Why does my Denon Stereo Receiver say “CHECK SIRIUS TUNER”?
- KKelly BurchAug 17, 2025
This message appears when the SiriusConnect Home Tuner is not properly connected. To resolve this, check that all connections are correct.
Why does my Denon Stereo Receiver say “CHECK SIRIUS TUNER”?
This message appears when the SiriusConnect Home Tuner is not properly connected. To resolve this, check that all connections are correct.
What to do if my Denon Stereo Receiver displays ”ANTENNA ERROR”?
The “ANTENNA ERROR” message indicates that the antenna is not connected. Ensure that the antenna connections are correctly made.
Why does my Denon Stereo Receiver display ”ACQUIRING SIGNAL”?
The message ”ACQUIRING SIGNAL” indicates that the signal cannot be received. This can occur while the SiriusConnect Home Tuner is connected. Try repositioning the antenna to improve signal reception.
What to do if my Denon Stereo Receiver displays ”INVALID CHANNEL”?
The “INVALID CHANNEL” message means that the channel you are trying to access is not available. Select another channel.
Why does my Denon Stereo Receiver say ”Call SIRIUS”?
The message ”Call SIRIUS” indicates that you are trying to access channels you are not subscribed to. If you subscribe to the channel, you will be able to receive it.
What to do if I cannot login to Rhapsody on my Denon Stereo Receiver and see “Username or Password is incorrect”?
If you are seeing the message “Username or Password is incorrect”, it means that your login information is not correct, or your trial period has expired. Here are some things you can try: * Check if the Username for Rhapsody has been properly entered. * Re-enter the Password. (Password is not displayed.)
Why does my Denon Stereo Receiver stop playing music in the middle of playback?
If your device stops playing in the middle of a song, it may be due to limitations of the trial period. When the trial period has finished, there is a limit to the playing time and number of tracks that can be played.
Why can't I play music on my Denon Stereo Receiver?
If you are unable to play music, it may be due to limitations of the trial period. When the trial period has finished, there is a limit to the playing time and number of tracks that can be played.
What to do if my Denon Stereo Receiver power turns off suddenly and the power indicator flashes red?
If your Denon Stereo Receiver's power suddenly turns off and the power indicator flashes red, it could be due to several reasons: * The protection circuit may have been activated because of a rise in internal temperature. In this case, turn off the power, wait for the unit to fully cool down, and then turn it back on. Also, ensure the set is placed in a well-ventilated area. * The core wires of the two speakers might be touching each other, or a core wire may be sticking out and touching the set’s rear panel, activating the protection circuit. To resolve this, first unplug the power cord, then twist the core wires tightly or terminate the speaker cables, and then reconnect. * Speakers with an impedance other than specified are being used. Use speakers with the specified impedance. *...
General| Audio Channels | 7.1 |
|---|---|
| Total Harmonic Distortion (THD) | 0.05% |
| Frequency Response | 10 Hz - 100 kHz |
| Frequency Response (+1, -3 dB) | 20 Hz - 20 kHz |
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Network Connectivity | Yes |
| Response Bandwidth | 10 Hz - 100 kHz |
| Signal-To-Noise Ratio | 102 dB |
| Input Sensitivity | 200 mV |
| Tuner Bands | AM/FM |
| HDMI Switching | Yes |
| Video Conversion/Scaling | Yes |
| Digital Sound Processor (DSP) | Yes |
| Signal-to-Noise Ratio (line, IHF-A) | 102 dB |
| Ethernet Port | Yes |
| USB Port | Yes |
| Power Output (8 ohms, 20Hz - 20kHz, 0.05% THD) | 130 W |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Input Impedance | 47 kOhms |
| Surround System Class | 7.1 |
| Input Sensitivity/Impedance | 200 mV / 47 kOhms |
| Supported Audio Formats | MP3, WMA, AAC, WAV |
| Power Output (Rated) | 130W per channel (8 ohms, 20Hz - 20kHz, 0.05% THD) |
| Dimensions (W x H x D) | 434 x 171 x 380 mm |
| DSP Presets | Multiple |
| Audio Inputs/Outputs | Multiple |
| Digital Audio Inputs/Outputs | Multiple |
