To Next PageTo Next PageWhat does “Not Support” mean on my Denon Receiver when using an iPod?
If “Not Support” is displayed on your Denon Receiver when using an iPod, it could be due to the following reasons: * The connected iPod may not be compatible. Ensure the iPod you are connecting is a compatible model. * The software version of the connected iPod may be outdated. Update to the latest version.
How to fix a Denon Receiver that does not turn on?
If your Denon Receiver isn't powering on, check the following: * Ensure the power plug is correctly inserted into the power outlet. * If the protection circuit is active, disconnect the power plug from the outlet, wait 5 to 10 seconds, and then plug it back in.
Why won't my Denon Receiver respond to the remote control?
If you're having trouble operating your Denon Receiver with the remote control, consider these points: * Replace the batteries with new ones if they are worn out. * Ensure you are within 23 ft / 7 m of the unit and within a 30° angle. * Remove any obstacles between the unit and the remote. * Verify the batteries are inserted correctly, matching the polarity marks. * Move the unit away from strong light sources like direct sunlight or fluorescent lights.
Why is my Denon Receiver subwoofer not producing sound?
If you're not getting any sound from the subwoofer connected to your Denon Receiver: * Check the subwoofer connections. * Make sure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes.” * If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
How to troubleshoot no audio output with HDMI on a Denon Receiver?
If you're experiencing no audio output with an HDMI connection on your Denon Receiver: * Check the HDMI connector connections. * If you want audio from the speakers, set “HDMI Audio Out” on the menu to “Amp.” * If you want audio from the TV, set “HDMI Audio Out” on the menu to “TV.”
Why is DTS sound not outputting on my Denon Receiver?
If DTS sound is not outputting from your Denon Receiver, set “Decode Mode” on the menu to “Auto” or “DTS.”
What does it mean if the power indicator is blinking red after turning on my Denon Receiver?
If, after turning on your Denon Receiver, the power indicator blinks red every 0.5 seconds, the unit's amplifier circuit has likely failed. Turn off the power and contact a DENON service advisor.
How do I turn on the display on my Denon Receiver?
If the display on your Denon Receiver is off, set “Display” on the menu to something other than “OFF”.
How to troubleshoot no sound from the subwoofer on Denon AVR-591?
If you're not getting any sound from your subwoofer with your Denon Stereo Receiver, first check the subwoofer connections and ensure the subwoofer is powered on. Then, go to the menu and set “Speaker Config.” – “Subwoofer” to “Yes.” Also, if “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or surround mode.
What to do if my Denon Receiver does not operate properly?
If your Denon Receiver isn't operating properly, try resetting the microprocessor.
General| Channels | 5.1 |
|---|---|
| Power Output | 75 W per channel (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Input Sensitivity/Impedance | 200 mV / 47 kohms |
| Signal-to-Noise Ratio | 98 dB |
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Audyssey | Audyssey MultEQ |
| HDMI Pass-Through | Yes |
| Tuner Bands | AM/FM |
| Preset Station Qty | 56 |
| Total Harmonic Distortion | 0.08% |
| Tuner Frequency Range | FM: 87.5 - 107.9 MHz, AM: 520 - 1710 kHz |
| Dolby Support | Dolby Digital, Dolby Digital Plus |
| DTS Support | DTS-HD Master Audio |
| Dimensions | 434 x 167 x 382 mm |
| Weight | 21.6 lbs (9.8 kg) |
