How do I fix reception issues with my Denon Stereo Receiver?
If your Denon Stereo Receiver isn't receiving signals well, resulting in noise or distortion, try these steps: * Adjust the antenna's orientation or position. * Separate the AM loop antenna from the unit. * Consider using an FM outdoor antenna. * Keep the antenna separate from other connection cables.
How to fix a Denon Receiver that does not turn on?
If your Denon Receiver isn't powering on, check the following: * Ensure the power plug is correctly inserted into the power outlet. * If the protection circuit is active, disconnect the power plug from the outlet, wait 5 to 10 seconds, and then plug it back in.
Why won't my Denon Receiver respond to the remote control?
If you're having trouble operating your Denon Receiver with the remote control, consider these points: * Replace the batteries with new ones if they are worn out. * Ensure you are within 23 ft / 7 m of the unit and within a 30° angle. * Remove any obstacles between the unit and the remote. * Verify the batteries are inserted correctly, matching the polarity marks. * Move the unit away from strong light sources like direct sunlight or fluorescent lights.
Why is my Denon Receiver subwoofer not producing sound?
If you're not getting any sound from the subwoofer connected to your Denon Receiver: * Check the subwoofer connections. * Make sure the subwoofer is powered on. * In the menu, set “Speaker Config.” – “Subwoofer” to “Yes.” * If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
How to turn on the display on a Denon AVR-591 Stereo Receiver?
If your Denon Stereo Receiver's display is off, go to the menu and set “Display” to something other than “OFF”.
What to do if no picture appears on my Denon AVR-591?
If no picture appears on your Denon Stereo Receiver, check the TV connection and ensure the TV input is set correctly.
What does it mean if the power indicator is blinking red after turning on my Denon Receiver?
If, after turning on your Denon Receiver, the power indicator blinks red every 0.5 seconds, the unit's amplifier circuit has likely failed. Turn off the power and contact a DENON service advisor.
How do I turn on the display on my Denon Receiver?
If the display on your Denon Receiver is off, set “Display” on the menu to something other than “OFF”.
How to troubleshoot no sound from the subwoofer on Denon AVR-591?
If you're not getting any sound from your subwoofer with your Denon Stereo Receiver, first check the subwoofer connections and ensure the subwoofer is powered on. Then, go to the menu and set “Speaker Config.” – “Subwoofer” to “Yes.” Also, if “Front” and “Center” are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or surround mode.
What to do if my Denon Receiver does not operate properly?
If your Denon Receiver isn't operating properly, try resetting the microprocessor.
Check all connections and ensure they are correct before powering on the unit.
Explains how temperature differences can cause condensation and affect operation.
Advises moving mobile phones away to prevent noise interference.
Instructions on how to safely move the unit by turning it off and unplugging it.
Guidance on cleaning the unit and avoiding certain chemical cleaners.
Describes the initial installation process for 5.1-channel speakers.
Explains how to connect 5.1-channel speakers, TV, and Blu-ray Disc player.
Details the procedure for powering on the unit and connected devices.
Guides through the Audyssey Auto Setup process for speaker configuration.
Instructions on how to play back Blu-ray discs and DVDs in surround sound.
Information on connecting various media and external devices to the unit.
Basic procedures for playing back audio and video content.
How to choose the appropriate surround sound mode for playback.
Installation and connection methods for speakers other than 5.1-channel systems.
Explains advanced functions and operations for better unit utilization.
Guide to menu operations for configuring audio, video, and other settings.
How to register preset codes to control external AV equipment.
Identifies and explains the various buttons and indicators on the front panel and display.
Includes trademark information, surround mode details, and explanations of terms.
Provides solutions for common problems encountered with the unit.
Lists the technical specifications for the audio, video, tuner, and other sections.
General| Channels | 5.1 |
|---|---|
| Power Output | 75 W per channel (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Input Sensitivity/Impedance | 200 mV / 47 kohms |
| Signal-to-Noise Ratio | 98 dB |
| HDMI Inputs | 4 |
| HDMI Outputs | 1 |
| Audyssey | Audyssey MultEQ |
| HDMI Pass-Through | Yes |
| Tuner Bands | AM/FM |
| Preset Station Qty | 56 |
| Total Harmonic Distortion | 0.08% |
| Tuner Frequency Range | FM: 87.5 - 107.9 MHz, AM: 520 - 1710 kHz |
| Dolby Support | Dolby Digital, Dolby Digital Plus |
| DTS Support | DTS-HD Master Audio |
| Dimensions | 434 x 167 x 382 mm |
| Weight | 21.6 lbs (9.8 kg) |
To Next Page
