– 17 – EN
DISC PLAYBACK
English
1 2 3 4 5 6
7 8 9
Getting started
• Turn on the power of the TV, amplifi er and any other
components which are connected to the DVD player.
• Make sure the TV and audio receiver (commercially
available) are set to the correct channel.
1 Press the POWER ON button.
• P-ON will appear briefl y on the display
panel.
2 Press the OPEN/CLOSE button to
open disc loading tray.
3 Place the disc on the tray, with the
label facing up.
4 Press the PLAY button.
•
The tray will close automatically, then playback will start
from the fi rst chapter or track of the disc. If the playback
does not start automatically, press the PLAY button.
•
When you play back the DVD with a title menu, it may appear
on the screen. In this case, refer to “Title Menu” on page 18.
5 Press the STOP button to stop playback.
NOTES:
• A “prohibited icon” may appear at
the top-right on the TV screen during
operation, warning that a prohibited
operation has been encountered by the
DVD player or the disc.
• With DVDs that use some titles for playback programme
signals, playback may start from the second title, or it
may skip these titles.
• During the playback of two layered disc, pictures may
stop for a moment. This happens when the 1st layer
switches to the 2nd layer. This is not a malfunction.
• The operation may vary when you play back DVDs with
disc menu or Video CDs with PBC or DivX
®
video fi les.
Refer to the manual accompanying the disc for details.
CANCELLING AND CALLING BACK PBC FUNCTION
3
1 Insert a Video CD.
2 Press the STOP button.
3 Press the Numeric buttons to enter the desired
Track number.
• PBC function is now cancelled and the playback of the
Video CD will start.
4 To call back PBC function, press the STOP button
twice, and then press the PLAY button.
• The title menu will appear on the TV screen.
1 Press the HDMI button on the front panel to select
the HDMI output mode.
The output mode changes as follows every time the
HDMI button is pressed.
• The HDMI indicator on the front panel lights up when
HDMI output mode is on.
480P/576P (Default):
Video output from the HDMI OUT jack at 480p/576p.
720P: Video output from the HDMI OUT jack at 720p.
1080: Video output from the HDMI OUT jack at 1080i.
1080P: Video output from the HDMI OUT jack at 1080p.
OFF: No video outputs from the HDMI OUT connector.
NOTES:
• Video and audio signals may be distorted temporarily
when switching to/from the HDMI output mode.
• Use a display equipment with an HDMI-compatible port.
• The HDMI indicator on the front panel fl ashes when
you select the HDMI output mode but there is no HDMI
cable.
• If you turn on the pure direct mode, both video and
audio signals through the HDMI output will be cut off
(press the PURE DIRECT button again to recover).
• You can check the HDMI connection status by pressing
the DISPLAY button during playback with the HDMI
output mode (refer to page 26).
• If the TV is not compatible with newly selected HDMI
output mode, the actual output mode will be kept the
one before changing the selection. When this occurs,
the newly selected mode will appear on the front
panel display (refer to page 11) while the actual output
resolution will be indicated by performing the on-screen
display as described in NOTE FOR HDMI DISPLAY on
page 26.
• Actual output signals for each HDMI mode vary with the
compatibility of the connected display device.
• You cannot select the HDMI output mode when the
setup menu is on the TV screen.
1 Press the PURE DIRECT button on the front
panel to output an analogue audio signal only (no
analogue video and HDMI signals will be output
and the display will be turned off). The higher
quality sound will be achieved.
NOTES:
• When the buttons below are pressed, the pure direct
mode will be released.
OPEN/CLOSE button (on both the remote and the front
panel), SETUP or DISPLAY button (on the remote),
ON/STANDBY or PURE DIRECT button (on the front
panel).
• The PURE DIRECT button will not function while
displaying the setup menu.
• If you turn on the pure direct mode while selecting
HDMI mode, both video and audio signals will not be
output.
1 Press the DIMMER NTSC/PAL button on the front
panel to select the desired brightness of the front
panel display. (BRIGHT, DIMMER or OFF)
• The default setting is BRIGHT.
NOTES:
• The brightness of the front panel display can be
adjusted from the setup menu. Details are on page 33.
• When you turn on the power next time, the brightness
of the front panel display will be as set in setup menu.
TV TYPE
Select a suitable video system according to the format of the
TV you connected.
1 Stop playback.
2 Press the DIMMER NTSC/PAL button on the front
panel more than 3 seconds.
The video system will be displayed on the front
panel display and TV screen.
Pure Direct Mode
HDMI Setup
Basic Playback
1080 1080P480P/576P 720P OFF
>
Brightness of the Front Panel Display
NTSC PALMULTI
E6GG0EDG1ED(EN)0601.indb17E6GG0EDG1ED(EN)0601.indb17 2007/06/0115:00:122007/06/0115:00:12
To Next Page
Loading...
Need help?
Video Outputs
Power
Weight and Dimensions
