DeWalt D27107 - Page 30

28
ENGLISH
English (original instructions)
EC-Declaration of Conformity
Machinery Directive
FLIP-OVER SAW
D27107/D27107XPS
DeWALT
declares that these products described under Technical Data are in compliance with:
2006/42/EC, EN61029-1:2009 +A.11:2010, EN61029-2-11:2012 +A11:2013.
These products also comply with Directive 2014/30/EU and 2011/65/EU. For more information,
please contact
DeWALT
at the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical file and makes this declaration
on behalf of
DeWALT
.
Markus Rompel
Vice President of Engineering, PTE-Europe
DeWALT
, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
19.06.2017
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to thesesymbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result
in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result
in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderateinjury.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may
result in propertydamage.

Denotes risk of electricshock.

Denotes risk offire.
Safety Instructions
WARNING! When using electric tools basic safety precautions should always
be followed to reduce the risk of fire, electric shock and personal injury including
thefollowing.
Read all these instructions before attempting to operate this product and save theseinstructions.
SAVE THIS MANUAL FOR FUTURE REFERENCE
General Safety Rules
1 . Keep work areaclear.
– Cluttered areas and benches inviteinjuries.
2 . Consider work areaenvironment.
– Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the
work area well lit (250300 Lux). Do not use the tool where there is a risk of causing fire or
explosion, e.g., in the presence of flammable liquids andgases.
3 . Work floor area.
– DO NOT use the stand on uneven surfaces. The stand is designed to be used on a flat,
stable surface. If the saw stand can slide around or wobbles, the power tool or the
workpiece cannot be evenly and securelyguided.
4 . Guard against electricshock.
– Avoid body contact with earthed surfaces (e.g., pipes, radiators, cookers and refrigerators).
When using the tool under extreme conditions (e.g., high humidity, when metal swarf is
being produced, etc.), electric safety can be improved by inserting an isolating transformer
or a (FI) earth-leakage circuit-breaker.
5 . Keep other personsaway.
– Do not let persons, especially children, not involved in the work, touch the tool or the
extension cord and keep them away from the workarea.
6 . Store idletools.
– When not in use, tools must be stored in a dry place and locked up securely, out of reach
ofchildren.
7 . Do not force thetool.
– It will do the job better and safer at the rate to which it wasintended.
8 . Use the righttool.
– Do not force small tools to do the job of a heavy duty tool. Do not use tools for purposes
not intended; for example do not use circular saws to cut tree limbs orlogs.
Congratulations!
You have chosen a
DeWALT
tool. Years of experience, thorough product development and
innovation make
DeWALT
one of the most reliable partners for professional power toolusers.
Technical Data
D27107 D27107XPS
Voltage V
AC
230 230
Type 7 5
(D27107
withworklight LED)
Power input W 2000 2000
Power output W 1080 1080
Max. blade speed min
-1
4000 4000
Blade diameter mm 305 305
Blade bore mm 30 30
Blade body thickness mm 2.1–2.2 2.1–2.2
Riving knife thickness mm 2.5 2.5
Automatic blade brake time s < 10 < 10
Weight kg 42 42
Cutting capacities
Mitre saw mode
Mitre (max. positions) left 48° 48°
right 48° 48°
Bevel (max. positions) left 48° 48°
right 2° 2°
Max. crosscut capacity at 90°/90° mm 205 x 63 205 x 63
Max. mitre cut capacity at 45° mm 160 160
Max. depth of cut 90° mm 90 90
Max. depth of bevel cut 45° mm 60 60
Max. depth of cut at 45° bevel, 45° mitre mm 60 60
Saw bench mode
Max. ripping capacity left/right mm 120/320 120/320
Depth of cut at 90° mm 80 80
Depth of cut at 45° mm 56 56
Noise values and/or vibration values (triax vector sum) according to EN61029:
L
PA
(emission sound pressure level) dB(A) 95,0 95.0
L
WA
(sound power level) dB(A) 106.0 106.0
K (uncertainty for the given sound level) dB(A) 3.0 3.0
Vibration emission value a
h
= m/s
2
2.1 2.1
Uncertainty K = m/s
2
1.5 1.5
The vibration and/or noise emission level given in this information sheet has been measured in
accordance with a standardised test given in EN61029 and may be used to compare one tool
with another. It may be used for a preliminary assessment ofexposure.

WARNING: The declared vibration and/or noise emission level represents the main
applications of the tool. However if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total workingperiod.
An estimation of the level of exposure to vibration and/or noise should also take
into account the times when the tool is switched off or when it is running but not
actually doing the job. This may significantly reduce the exposure level over the total
workingperiod.
Identify additional safety measures to protect the operator from the effects of vibration
and/or noise such as: maintain the tool and the accessories, keep the hands warm
(relevant for vibration), organisation of workpatterns.
NOTE: This device is intended for the connection to a power supply system with maximum
permissible system impedance Zmax of 0.28  at the interface point (power service box) of
user’ssupply.
The user has to ensure that this device is connected only to a power system which fulfils the
requirement above. If necessary, the user can ask the public power supply company for the
system impedance at the interfacepoint.
FLIPOVER SAW
D27107, D27107XPS