DeWalt D36000 - MAINTENANCE

10
ENGLISH
Protecting the Environment
w
Separate collection. Products marked with this symbol must not be disposed of with
normal householdwaste.
Products contain materials that can be recovered or recycled reducing the demand
for raw materials. Please recycle electrical products according to local provisions.
Further information is available at www.2helpU.com.
Storage
Store the equipment and accessories out of children's reach in a dark and dry place at above
freezing temperature. The ideal storage temperature is between 5 °C and 30 °C.
Stand
D240001 Heavy Duty Tile Saw Stand
Range of Cutting Discs Available
DT3734 Wet tile diamond saw blade for cutting ceramic, porcelain tiles and stone
DT3733 Wet tile diamond saw blade for cutting tiles
Optional Accessories

WARNING: Since accessories, other than those offered by DeWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only DeWALT recommended accessories should be used with thisproduct.
Consult your dealer for further information on the appropriateaccessories.
Before use, carefully check the cutting disk cover to determine that it will operate properly.
Ensure that mud, or work-piece particles cannot lead to blockage of one of thefunctions.
In case of workpiece fragments jammed between cutting disc and guard disconnect the
machine from the power supply and follow the instructions given in section Mounting the
cutting disc. Remove the jammed parts and reassembling the cuttingdisc.
Keep the ventilation slots clear and regularly clean the housing with a softcloth.
The following cleaning operations must be performed everyday.
1. Insert the water pump into a bucket of clean water and pump the water through the
hosesystem.
2. Wipe the rails and support arm with a grout sponge or arag.
3. Spray the water basin and the sliding table with clear water. Wipe any dust residue away
with a groutsponge.
D
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non‑metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into aliquid.
C
Lubrication
Your power tool requires no additionallubrication.
Draining the Water Basin (Fig. ###)
The water basin must be drained after eachuse.
1. Place a suitable container under the drain plug
58
.
2. Remove the drainplug.
3. Allow ample time for the liquid todrain.
4. After the liquid has been drained, re-install the drainplug.
5. Dispose of the liquid with due care for theenvironment.
MAINTENANCE
Your power tool has been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper tool care and
regularcleaning.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. An accidental start‑up can causeinjury.

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by a DeWALT factory service centre or a DeWALT
authorized service centre. Always use identical replacement parts.
If the supply cord is damaged, it must be replaced only by DeWALT or an authorised
serviceorganisation.
Transporting (Fig. O, Z)
The detachable parts can be stored in the water basin for easytransportation.
1. Drain the water basin. SeeMaintenance.
2. Remove the edge guide and the extensiontable.
3. Lock the cutting cart inposition.
4. Remove the watercollectors.
5. Lift the machine out of the water basin asshown.
6. Place the collectors into the water basin in the orientation asshown.
7. Turn the water basin upsidedown.
8. The edge guide and the extension table can be placed in the water basin beforenested.
9. Lift and hold the machine at the carrying points
61
asshown in Fig. N.

WARNING: When carrying the machine, always seek assistance. The machine is
too heavy for one person tohandle. Always lock the cutting cart before moving or
transporting saw.