DeWalt DCF815 Original Instructions

8
ENGLISH
Only for indooruse.
Discard the battery pack with due care for
theenvironment.
Charge DeWALT battery packs only with designated
DeWALT chargers. Charging battery packs other
than the designated DeWALT batteries with a
DeWALT charger may make them burst or lead to
other dangeroussituations.
Do not incinerate the batterypack.
Package Contents
The package contains:
1 Cordless impact driver or impact wrench
1 Charger
2 Battery packs
1 Impact rated screwdriver bit (DCF815)
1 Kitbox
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1
Trigger switch
2
Forward/reverse button
3
Chuck collar (DCF815)
4
6.35 mm hex quick-release chuck (DCF815)
5
Battery release button
6
Battery pack
7
Worklight
8
Main handle
9
Hog ring (DCF813)
Intended Use
The impact driver and impact wrench are designed for
professional impact fastening applications. The impact function
makes this tool particularly useful for driving fasteners in wood,
metal andconcrete.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
This impact driver and impact wrench are professional
powertools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
Your DeWALT charger is double insulated in
accordance with IEC60335; therefore no earth wire
isrequired.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the
DeWALT
serviceorganisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1 mm
2
; the maximum length
is30m.
When using a cable reel, always unwind the cablecompletely.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can causeinjury.

WARNING: Use only DeWALT battery packs andchargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
NOTE: Make sure your battery pack
6
is fullycharged.
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack
6
with the rails inside the tool’s
handle (Fig. C).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the release button
5
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.

DeWalt DCF815 Specifications

General

Voltage	12V
Drive Size	1/4 inch
Tool Weight	2.2 lbs
LED Light	Yes
Chuck Type	Quick Release
No Load Speed	0-2450 RPM
Impacts per Minute	0-3400 IPM
Tool Length	6.25 in
Battery Type	Lithium-Ion