DeWalt DCS367 - Page 16

ENGLISH
16
EC-Declaration of Conformity
Machinery Directive
Reciprocating Sabre Saw
DCS367
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN62841-1:2015+A11:2022,
EN62841-2-11:2016+ A1:2020 + A11:2024.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf ofDeWALT.
Markus Rompel
Vice President of Engineering, PTE-Europe
DeWALT, Richard-Klinger-Straße 11,
65510, Idstein, Germany
30.09.2024
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.

DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderateinjury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in propertydamage.

Denotes risk of electricshock.

Denotes risk offire.
GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
powertool.
WARNING: Read all safety warnings, instructions,
illustrations, and specifications in this manual,
including the battery and charger sections provided in
an original tool manual or the separate Batteries and
Chargers manual. Manuals can be obtained by contacting
Customer Service (refer to the back page of thismanual).
Technical Data
DCS367
Voltage V
DC
18
Type 10
Battery type Li-Ion
No-load speed min
-1
0–2900
Stroke length mm 28.6
Cutting capacity in wood/metal profiles/plastic tubes mm 280/100/130
Weight (without battery pack) kg 2.27
Noise values and/or vibration values (triax vector sum) according to
EN62841-2-11:
L
PA
(emission sound pressure level) dB(A) 92
L
WA
(sound power level) dB(A) 100
K (uncertainty for the given sound level) dB(A) 3
While cutting board
Vibration emission value ah,
B
= m/s
2
27.0
Uncertainty K = m/s
2
4.6
While cutting wooden beam
Vibration emission value a
h,WB
= m/s
2
25.0
Uncertainty K = m/s
2
4.6
The vibration and/or noise emission level given in this
information sheet has been measured in accordance with
a standardised test given in EN62841 and may be used to
compare one tool with another. It may be used for a preliminary
assessment ofexposure.

WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However if the
tool is used for different applications, with different accessories or
poorly maintained, the vibration and/or noise emission may differ.
This may significantly increase the exposure level over the total
workingperiod.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job.
This may significantly reduce the exposure level over the total
workingperiod.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm (relevant for vibration),
organisation of workpatterns.
English (original instructions)
CORDLESS RECIPROCATING SABRE SAWS
DCS367