DeWalt DW714 - Maintenance; Protecting the Environment; Specifications

ENGLISH
59
Fig. KK
Dust Extraction (Fig. A, C)
• Fit the dustbag
32
onto the dust spout
14
.

WARNING: Whenever possible, connect a dust
extraction device designed in accordance with the
relevant regulations regarding dust emission.
Connect a dust collection device designed in accordance
with the relevant regulations. The air velocity of externally
connected systems shall be 20 m/s ±2 m/s. Velocity
to be measured in the connection tube at the point of
connection, with the tool connected but not running.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from
the power source before attempting to move it,
change accessories or make any adjustments.
Your D
e
WALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
DO NOT use lubricants or cleaners (particularly spray
or aerosol) in the vicinity of the plastic guard. The
polycarbonate material used in the guard is subject to
attack by certain chemicals.
1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even though
slots are provided to allow debris to pass through, some
dust willaccumulate.
3. The brushes are designed to give you several years of
use. To replace the brushes refer to Brushes or return
the tool to the nearest service center for repair. A list of
service center locations is packed with your tool.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performingthis.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
Repairs

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a
DeWALT
factory service center
or a
DeWALT
authorized service center. Always use
identical replacementparts.
Protecting the Environment
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions.
Specifications
Capacity of cut
47° miter left , 52° right
45° bevel left, 0° right
0 degree miter, 0 degree bevel
Max. Height 3.5” (89 mm) Result Width 3.7” (95 mm)
Max. Width 5.1” (130 mm) Result Height 2.7” (68 mm)
45 degree miter, 0 degree bevel
Max. Height 3.5” (89 mm) Result Width 2.6” (67 mm)
Max. Width 3.6” (91 mm) Result Height 2.7” (68 mm)
0 degree miter, 45 degree bevel
Max. Height 2.0” (50 mm) Result Width 3.7” (95 mm)
Max. Width 5.1” (130 mm) Result Height 1.6” (40 mm)
45 degree miter 45 degree bevel
Max. Height 1.8” (45 mm) Result Width 2.8” (70 mm)
Max. Width 3.6” (91 mm) Result Height 1.6” (40 mm)
Power 1650 W
Revolutions per minute 4600 RPM
Automatic electric brake Yes
DW714-AR DW714-B2 DW714-B3 DW714-BR DW714-B2C
220V 220V 120V 127V 220V
~50Hz ~50–60Hz ~50–
60Hz
~60Hz ~50Hz