DeWalt DWE7492 - Component Installation and Mounting; Mounting Blade Guard and Riving Knife; Mounting the Throat Plate; Fitting the Rip Fence

14
ENGLISH

WARNING: Do not touch the saw blade after working
before it has cooled. The saw blade becomes very hot
whileworking.
NOTE: This tool has blade installed fromfactory.
1. Raise the saw blade arbor to its maximum height by turning
the blade height adjustment wheel
6
clockwise.
2. Remove the throat plate
16
. Refer to Mounting the
ThroatPlate.
3. Using wrenches
20
, loosen and remove the arbor
nut
22
and flange
24
from the saw arbor by turning
anti-clockwise.
4. Place the saw blade on to the spindle
23
making sure the
teeth of the blade
2
point down at the front of the table.
Assemble the washers and arbor nut to the spindle and
tighten arbor nut
22
as far as possible by hand, making sure
that the saw blade is against the inner washer and the outer
flange
24
is against the blade. Ensure the largest diameter
of the flange is against the blade. Ensure the spindle and
washers are free from dust anddebris.
5. To keep the spindle from rotating when tightening the
arbor nut, use the open end of the blade wrench
20
to
secure thespindle.
6. Using the arbor wrench, tighten the arbor nut
22
by
turning itclockwise.
7. Replace the throatplate.

WARNING: Always check the rip fence pointer and the
blade guard assembly after having changed theblade.
Mounting the Blade Guard Assembly/
Riving Knife (Fig.A,D)

WARNING: Use the guard assembly for all
throughcutting.

WARNING: Use the riving knife for non-through-cutting
when blade guard assembly cannot beused.

WARNING: Do not insert both the blade guard assembly
and the non-through-cutting riving knife into the clamp
at the same time.
NOTE: The saw is shipped with the non-through-cutting riving
knifeinstalled.
1. Raise the saw blade arbor to its maximumheight.
2. Install blade guard assembly by pulling the guard release
lever
12
and inserting either the non-through-cutting
riving knife
52
or the blade guard assembly
11
until it
bottomsout.
3. Release lever, make sure clamp plates are fully closed and
clamp the splittersecurely.

WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the blade
guard assembly for proper alignment and clearance
with saw blade. Check alignment after each change of
bevelangle.

WARNING: To reduce the risk of serious personal injury,
DO NOT operate saw if blade assembly is not securely
clamped inplace.
When properly aligned, the splitter
13
or riving knife
52
will
be in line with the blade at both table top level, and at the top
of the blade. Using a straight edge, ensure that the blade
2
is
aligned with the splitter
13
 or riving knife
52
. With power
disconnected, operate the blade tilt and height adjustments
through the extremes of travel and insure the blade guard
assembly clears the blade in alloperations. Refer to Aligning
Guard Assembly/Splitter to Blade.

WARNING: Correct mounting and alignment of the blade
guard assembly is essential to safe operation!
To Remove the Blade Guard Assembly/
Riving Knife (Fig.D)
1. Pull the guard release lever
12
.
2. Lift up on blade guard assembly
11
or riving knife
52
.
Mounting the Throat Plate(Fig.E)
1. Align the throat plate
16
as shown in FigureE, and insert
the tabs on the back of the throat plate into the holes on the
back of the tableopening.
2. Turn the locking screw
40
clockwise 90° to lock the table
insert inplace.
3. The throat plate includes four adjustment screws
25
which
raise or lower the throat plate. When properly adjusted, the
front of the throat plate should be flush or slightly below the
surface of the table top and secured in place. The rear of the
throat plate should be flush or slightly above the tabletop.

WARNING: Never use the machine without the throat
plate. Immediately replace the throat plate when worn
ordamaged.
To Remove the Throat Plate
1. Remove the throat plate
16
by turning the locking
screw
40
90˚ anti-clockwise
2. Using finger hole
26
, pull throat plate up and forward
to expose the inside of the saw. DO NOT operate the saw
without the throat plate. If using a dado blade, use proper
dado throat plate (sold separately).
Fitting the Rip Fence(Fig.F)
The rip fence can be installed in two positions on the
right(Position 1 for 0 mm to 62 cm ripping, and Position 2 for
20.3 cm to 82.5 cm ripping) and one position on the left of your
tablesaw.
1. Unlock the rip fence latches
18
.
2. Holding the fence at an angle, align the locator
pins(front and back)
29
on the fence rails with the fence
headslots
30
.
3. Slide the head slots onto the pins and rotate the fence down
until it rests on therails.
4. Lock the fence in place by closing the front and back
latches
18
onto therails.
Bench Mounting(Fig.A)

CAUTION: To reduce the risk of personal injury, make sure
table saw is firmly mounted to a stable surface beforeuse.