DeWalt DWEHF1838K - Tool;Fastener Specifications

TOOL SPECIFICATIONS
All dimensions in inches unless otherwise specified.
-5-
Operating Pressure
70 to 120 psig (4.9 - 8.4 kg/cm
2
). Select the operating pressure in this range for best fastener performance.
DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
The DWEHF1838K requires 1.94 cubic feet per minute or cfm (55 liters per minute or L/min) of free air at
80 PSI (5.6 kg/cm
2
) to operate at a rate of 60 fasteners per minute. The DWLHF2025K requires 1.90 cubic
feet per minute or cfm (54 liters per minute or L/min) of free air at 80 PSI (5.6 kg/cm
2
) to operate at a rate
of 60 fasteners per minute. To determine the appropriately sized air compressor, take the actual rate
at which the tool will be run and compare the required cfm (L/min) to the compressor’s free air delivery
(cfm or L/min) at 80 PSI (5.6 kg/cm
2
).
For example, if your fastener usage averages 30 fasteners per minute, you need 50% of the required air volume
(cfm or L/min) that is required to operate the tool at the rate of 60 fasteners per minute. In this case, be sure
that your air compressor can deliver a minimum of 0.97 cfm (27.5 L/min) at 80 PSI (5.6 kg/cm
2
) for optimum
performance.
*Visit www.
DeWALT
.com for further details.
NOTE:
D
e
WALT tools have been engineered to provide superior customer satisfaction and are designed to achieve
maximum perfomance when used with precision D
e
WALT fasteners engineered to the same exacting standards.
D
e
WALT cannot assume responsibility for product performance if our tools are used with fasteners
or accessories not meeting the specific requirements established for genuine D
e
WALT fasteners
andaccessories.
DWEHF1838K DWLHF2025K
Description 18-ga Flooring Stapler 20-ga Flooring Stapler
Engine Type Oil-free Oil-free
Operation Pressure Range 70-120 psig (4.9 - 8.4 kg/cm
2
) 70-120 psig (4.9 - 8.4 kg/cm
2
)
Maximum Operation Pressure 120 psig (8.4 kg/cm
2
) 120 psig (8.4 kg/cm
2
)
Fastener Type DNS181XX-2 Series DWCS20100
Fastener Gauge 18 Gauge 20 Gauge
Fastener Range 1” - 1-1/2” (25 mm - 38 mm) 1” (25 mm)
Magazine Capacity 100 125
Length 9-1/4” (235 mm) 9-1/4” (235 mm)
Width 2-3/4” (70 mm) 2-3/4” (70 mm)
Height 9-7/8” (251 mm) 8.5” (216 mm)
Weight 3.5 lb (1.57 kg) 2.9 lb (1.32 kg)
Tool Model
Fastener
Type
Fastener SKU
Crown
Width
Gauge Length
DWEHF1838K Staples
DNS18100-2 1/4” (6.3 mm) 18
1”
(25 mm)
DNS18125-2 1/4” (6.3 mm) 18
1-1/4”
(31.75 mm))
DNS18150-2 1/4” (6.3 mm) 18
1-1/2”
(38 mm)
DWLHF2025K Staples
DWCS20100
3/16”
(4.7 mm)
20
1”
(25 mm)
FASTENER SPECIFICATIONS