DeWalt XR DCF961 - Machinery Directive; Impact Wrench; Definitions: Safety Guidelines

ENGLISH
16
English (original instructions)
18V XR 1/2" HIGH TORQUE IMPACT WRENCH WITH HOG
RING ANVIL
18V XR 3/4" HIGH TORQUE IMPACT WRENCH WITH HOG
RING ANVIL
DCF961, DCF964
WARNING: Read all safety warnings, instructions,
illustrations, and specifications in this manual,
including the battery and charger sections provided in
an original tool manual or the separate Batteries and
Chargers manual. Manuals can be obtained by contacting
Customer Service (refer to the back page of thismanual).
Technical Data
DCF961 DCF964
Voltage V
DC
18 18
Type
1 1
Battery type
Li‑Ion Li‑Ion
No load speed min
‑1
0‑440/800/1200 0‑440/575/1200
Impact rate min
‑1
0–1890 0–2015
Max tightening torque
Precision Wrench™ mode
Low mode
Medium mode
High mode
Nm
Nm
Nm
Nm
1496
135
1220
1626
1728
677
1138
1925
Max breakaway torque Nm 2372 2576
Weight (without battery pack) kg
3.5 3.7
Noise values and vibration values (triax vector sum) according to EN62841‑2‑2:
L
PA
(emission sound pressure
level)
dB(A) 100 100
L
WA
(sound power level)
dB(A) 108 108
K (uncertainty for the given
sound level)
dB(A) 3 3
Vibration emission value a
h
=
m/s
2
21.0 16.0
Uncertainty K = m/s
2
6.3 4.4
and the accessories, keep the hands warm (relevant for vibration),
organisation of workpatterns.
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN 62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment ofexposure.

WARNING: The declared vibration and/or noise emission level
represents the main applications of the tool. However, if the tool is
used for different applications, with different accessories or is poorly
maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total workingperiod.
An estimation of the level of exposure to vibration and/or noise should
also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce
the exposure level over the total workingperiod.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
EC‑Declaration of Conformity
Machinery Directive
Impact Wrench
DCF961, DCF964
DeWALT declares that these products described under Technical
Data are in compliance with:
2006/42/EC, EN 62841-1:2015+A11:2022,
EN62841-2-2:2014+AC:2015.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at the
following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf ofDeWALT.
Markus Rompel
Vice-President Engineering, PTE-Europe
DeWALT, Richard-Klinger-Straße 11,
65510, Idstein, Germany
30.07.2024
a
WARNING: To reduce the risk of injury, read the
instructionmanual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.

DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderateinjury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in propertydamage.

Denotes risk of electricshock.

Denotes risk offire.
GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or seriousinjury.