What to do if my Dexter Laundry Washer machine starts and does not operate?
If your Dexter Laundry Washer starts but doesn't operate, check the yellow enable wires from the PCB relay board connection P13 & P14 to the VFD. Also, check the connection of the orange wire at P15 from the door switches.
What to do if cold water does not enter the tub in wash cycle of my Dexter Laundry Washer?
If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at the terminals and replace it if there's no continuity. Also, check for 24 VAC (50 Hz) power from the main relay PCB. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Finally, check the black and white wire at the Molex plug on the main PCB controller P21 connection and at the PCB relay board P20 connection, and examine the pressure switch continuity between terminal contacts. If no continuity, check the pressure switch hose for obstruction. If the hose is okay then change the pressure switch.
What to do if hot water does not enter the tub in wash cycle of my Dexter Laundry T-300 Washer?
If hot water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at the terminals and replace it if there's no continuity. Also, check for 24 VAC (50 Hz) power from the main relay PCB. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Finally, check the black and white wire at the Molex plug on the main PCB controller P21 connection and at the PCB relay board P20 connection, and examine the pressure switch continuity between terminal contacts. If no continuity, check the pressure switch hose for obstruction. If the hose is okay then change the pressure switch.
What to do if my Dexter Laundry T-300 Washer door does not lock?
If the door of your Dexter Laundry Washer isn't locking, first check the display for a fault code, specifically 'DOOR LOCK ERROR,' and follow the tests described in the fault code section if it appears. Next, verify that the door locking motor is receiving 24 VAC (50 Hz) from the main relay PCB; if it is, replace the motor. Also, check for continuity through the door latch switch when the door is closed; adjust or replace the switch if there's no continuity.
Why is my Dexter Laundry T-300 Washer vibrating excessively?
Excessive vibration in your Dexter Laundry Washer can stem from a few key areas. First, check the mounting system's strength, including the concrete or base, and ensure the mounting bolts are tightened. A worn drive belt can also cause vibration and noise, so inspect its condition. Lastly, be aware that small loads can contribute to out-of-balance loading, increasing vibration.
General| Brand | Dexter Laundry |
|---|---|
| Model | T-300 |
| Category | Washer |
| Language | English |
Defines symbols indicating prohibited actions and safety mandates.
Explains symbols related to general caution, hazards, and potential dangers.
Defines symbols providing additional information or reminders for users.
Lists and identifies different Dexter washer models and their designations.
Describes the general features, materials, and operational aspects of the washers.
Clarifies technical terms and acronyms used in the manual for user understanding.
Technical data for standard vended washer models, including dimensions and capacity.
Technical data for express vended washer models, including dimensions and capacity.
Technical data for Stacked Washer/Dryer (SWD) models, including dimensions and capacity.
Step-by-step instructions for properly installing the washing machine, including foundation and connections.
Guidelines for operating the washer, selecting cycles, and avoiding improper use.
Procedures for daily and quarterly checks and cleaning to ensure machine reliability.
Instructions for setting up and customizing washer features, cycles, and pricing.
Information on error codes and their meanings for troubleshooting washer issues.
Guidance for qualified personnel on repair, maintenance, and problem-solving.
Lists available accessories and common service parts for the washing machines.
Explains the symbol for Waste Electrical and Electronic Equipment and its disposal significance.
Identifies the manufacturer and their authorized representative for compliance matters.
Lists the specific washer models covered by the declaration of conformity.
Cites the directives and standards to which the product conforms.
To Next Page
