Why Dexter Laundry Washer water level is too high?
If the water level in your Dexter Laundry Washer is too high, check the pressure switch hose for any blockages. Also, check the pressure switch for an opening circuit across its terminals. If the contacts do not open, replace the switch.
What causes excessive vibration in Dexter Laundry Washer?
If your Dexter Laundry Washer experiences excessive vibration, check the strength of the mounting structure, concrete, or base, and ensure the mounting bolts are tightened. A worn drive belt or damaged pulleys can also cause vibration and noise, so inspect these components. Be sure you wash recommended load size as specified for washer model (in lb/kg). Small loads contribute to out of balance loading and increase vibration.
What causes water comes in but level does not rise in Dexter Laundry T-950?
If water comes into your Dexter Laundry Washer but the level does not rise, check the drain valve for blockage and the drain valve motor and gear train. If there is power but the drain valve does not close, replace the valve. Check for power to the drain valve; if there's no power, check the (brown/yellow) circuit for power. Also, check or replace the water valve diaphragms.
What to do when my Dexter Laundry T-950 Washer starts but does not operate?
If your Dexter Laundry Washer starts but doesn't operate, verify that the yellow enable wires from the relay PCB P13 & motor P14 to the VFD are connected and advancing through the cycle. Check the fault code on the VFD before removing power from the drive. Also, check the orange P-15 wire for a signal from the door switches.
Why Dexter Laundry T-950 has no hot water in detergent dispenser?
If there's no hot water in the detergent dispenser of your Dexter Laundry Washer, check the water valve coil for continuity at its terminals and replace it if there's no continuity. Note that 120 VAC (60 Hz) or 24 VAC (50 Hz) power is only on for 20 seconds in the wash bath. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating. Also, check the black & white wire harness (P-20).
Why does my Dexter Laundry Washer only tumble in one direction?
If your Dexter Laundry Washer only tumbles in one direction, review the indicator lights displayed on the VFD. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
Why Dexter Laundry T-950 machine does not start?
If your Dexter Laundry Washer isn't starting, several factors could be at play. Begin by examining the power supply, checking circuit breakers, voltage, power leads, and connections. Ensure the front display LED is lit. Next, verify the door switch for continuity when closed; adjust or replace if necessary. Inspect the control breaker or fuse for continuity and replace if needed. Check the control transformer's voltage output. Ensure all wire connections on the PCB board and relay PCB are secure. Also, confirm that the door lock mechanism is receiving the correct voltage after pressing the start button. Lastly, inspect the data cable phone type connectors between the PCB and VFD, ensuring they are properly plugged in after removing power.
Why hot or cold water does not enter the tub of Dexter Laundry Washer?
If hot or cold water does not enter the tub of your Dexter Laundry Washer, check to ensure that the water valve is operating. If it is not, check for 120VAC to the water valve from the Input/Output PCB. If there is 120VAC, change the water valve. If there is no voltage, check the Input/Output PCB. Also, check the water inlet screens for blockage and clean if necessary. Ensure that the water is turned on and operating. Check the pressure switch hose for holes and ensure the inlet end of the large part of the hose is lower than the rest of the hose and free of debris. The pressure switch must be in the empty position to close the circuit to the Input/Output PCB. The green Empty light #14 on the Input/Output PCB must be lighted. Check the pressure switch for continuity across terminals #31 & ...
How to open a Dexter Laundry Washer door that will not open?
If the door of your Dexter Laundry Washer won't open, check if the thermoactuator and its mechanism are stuck or binding. Ensure the locking thermoactuator is not receiving 24VAC during the last 1 1/2 minutes of the cycle and that the unlocking thermoactuator is receiving 24VAC during the last minute. If the timing and voltage are correct, replace the thermoactuator. Also, verify that the door rod from the mechanism to the lock assembly is long enough to allow the lock assembly to disengage; adjust the rod or the position of the mechanism if needed. Check that the door lock mechanism is not stuck closed; if it is, replace it.
Why is there no cold water entering the tub in my Dexter Laundry T-950 Washer during wash?
If no cold water is entering the tub of your Dexter Laundry Washer during the wash cycle, start by checking the water valve coil for continuity at the terminals and replace it if necessary. Inspect the water inlet screens for any blockage and clean them if needed. Ensure that the water supply is turned on and functioning correctly. If the appropriate voltage is not present at the valve, refer to the wiring diagram for your specific washer model. Check for voltage at the P4 Connector on the Relay PCB and for LED indication that the appropriate relay is activated. Check the pressure switch continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and if the hose is clear, replace the pressure switch.
General safety advice and warnings for operating the washer.
Daily and quarterly checks for optimal washer performance and longevity.
Guidelines for concrete floors and bases to ensure stable washer installation.
Details on reinforced concrete floors and pad types for installation.
Methods and options for securely anchoring the washer to the floor.
Step-by-step guide to loading, selecting cycles, and starting the washing process.
Explains the function of the emergency stop button and the safety door lock mechanism.
Instructions for accessing and navigating the programming menus on the washer control.
How to set vend prices and coin acceptor values for the washer.
Configuration of bath times, temperatures, and spin speeds for various wash cycles.
Common causes and remedies when the washer fails to power on or initiate.
General| Model | T-950 |
|---|---|
| Control Type | Microprocessor |
| Phase | 3 |
| Width | 46.5 in (1181 mm) |
| Depth | 52.5 in (1334 mm) |
| Height | 57.5 in (1461 mm) |
To Next Page
