Dexter Laundry T-900 User Manual (English)

Other manuals for Dexter Laundry T-900

Operators Manual Installation & Operation Instructions340 pages

Parts & Service Manual77 pages

Service Manual116 pages

Operator's Manual68 pages

Questions and Answers:

C
Christine FernandezSep 7, 2025
What to do if cold water does not enter the tub in wash cycle of my Dexter Laundry T-900?
- S
  Savannah Glass MDSep 7, 2025
  If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at the terminals and replace it if there's no continuity. Also, check for 24 VAC (50 Hz) power from the main relay PCB. Inspect the water inlet screens for blockage and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Finally, check the black and white wire at the Molex plug on the main PCB controller P21 connection and at the PCB relay board P20 connection, and examine the pressure switch continuity between terminal contacts. If no continuity, check the pressure switch hose for obstruction. If the hose is okay then change the pressure switch.
J
James NicholsAug 27, 2025
What causes excessive vibration in Dexter Laundry T-900 Washer?
- E
  Eric RichardsonAug 27, 2025
  If your Dexter Laundry Washer experiences excessive vibration, check the strength of the mounting structure, concrete, or base, and ensure the mounting bolts are tightened. A worn drive belt or damaged pulleys can also cause vibration and noise, so inspect these components. Be sure you wash recommended load size as specified for washer model (in lb/kg). Small loads contribute to out of balance loading and increase vibration.
J
Justin GeorgeAug 28, 2025
What causes water comes in but level does not rise in Dexter Laundry T-900?
- C
  cruzmatthewAug 28, 2025
  If water comes into your Dexter Laundry Washer but the level does not rise, check the drain valve for blockage and the drain valve motor and gear train. If there is power but the drain valve does not close, replace the valve. Check for power to the drain valve; if there's no power, check the (brown/yellow) circuit for power. Also, check or replace the water valve diaphragms.
B
Brooke YoungAug 29, 2025
Why water does not flush softener compartment of Dexter Laundry T-900 Washer?
- M
  Michael SextonAug 29, 2025
  If water does not flush the softener compartment of your Dexter Laundry Washer, check to ensure that the water valve is operating. If not, check for 120VAC to the water valve from the Input/Output PCB. If there is 120VAC, change the water valve. If there is no voltage check the Input/Output PCB. Also, check all screens for obstructions and clean them. Ensure that the water is turned on and operating.
J
James GreenSep 8, 2025
What to do if my Dexter Laundry T-900 machine starts and does not operate?
- L
  Laura GallegosSep 8, 2025
  If your Dexter Laundry Washer starts but doesn't operate, check the yellow enable wires from the PCB relay board connection P13 & P14 to the VFD. Also, check the connection of the orange wire at P15 from the door switches.
S
Stacey LopezSep 10, 2025
What to do if water drains slowly from my Dexter Laundry T-900 Washer?
- Y
  yharrisonSep 10, 2025
  If water is draining slowly from your Dexter Laundry Washer, check the hoses and drain valve for blockages. Ensure the building drain is of adequate size and inspect building drains for blockages.
S
Samuel HaleySep 4, 2025
What to do if my Dexter Laundry Washer does not stop?
- R
  Rodney MccormickSep 4, 2025
  If your Dexter Laundry Washer does not stop, remember that the main PCB controls the time cycle at the end of the cycle. Also, check the braking resistors for continuity and verify the ohms resistance by Molex.
A
Amy BarnesSep 4, 2025
Why is there water leakage around loading door of Dexter Laundry T-900?
- M
  Michael KellerSep 4, 2025
  If water is leaking around the loading door of your Dexter Laundry Washer, the door may need adjustment due to abuse or wear. Check the tightness around the perimeter using a dollar bill. Adjust the left to right tightness by shims at the door lock or hinge side, centering the gasket to the tub opening before tightening the door to hinge bolts. Chalk may be used on the tub front to show the point of contact with the tub. If the gasket is deformed, worn, or damaged, replace it.
D
Debra MitchellSep 1, 2025
Why my Dexter Laundry T-900 tumbles in one direction?
- A
  Andrea CampbellSep 1, 2025
  If your Dexter Laundry Washer tumbles in only one direction, remove the inspection cover at the rear and record any numbers or letters displayed. Refer to the fault code section for more information. Also, inspect the yellow enable wires from the main relay PCB and at the VFD.
F
fmuellerSep 1, 2025
Why no cold water to tub in wash for Dexter Laundry T-900 Washer?
- B
  briansuttonSep 1, 2025
  If cold water isn't entering the tub during the wash cycle of your Dexter Laundry Washer, start by checking the water valve coil for continuity at its terminals; replace it if there's no continuity. Next, inspect the water inlet screens for blockages and clean them if necessary. Ensure that the water supply is turned on and operating correctly. Check the black or white wires at the Molex plug on the PCB at the main controller and at the relay PCB. Lastly, test the pressure switch for continuity between terminal contacts; if there's no continuity, check the pressure switch hose for obstructions, and replace the switch if the hose is clear.