
The information contained here are property of DIGITAX AutomotiveElectronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
partyisstrictlyprohibited.

41
Nr. Functions Value
337 On service messages use normal font? No / Yes
from Q 338 to Q 339 available for any possible software extension
FIXED COST FARE (forfait)
340 Enable appl. of cost with num. keypad? - Enable the application of a fixed cost with the numeric keypad?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
341 Enable programming forfait with front keys? - If yes then, with the taximeter in Hired and pressing the keys K1 + K4 together, the forfait amount can be programmed on
the primary display. On the secondary display the text FORFA will be shown.
Programming:
pressing key K1 increases the amount with 1 unit pressing key K2 increases the amount with 10 units;
pressing key K3 increases the amount with 100 units pressing key K4 increases the amount with 1000 units;
pressing keys K3 + K4 cancels the modifications made up to this point pressing key OP the forfait programming is exited.
Once exited from the forfait programming the amount shown on the display will not change anymore independently from the run distance or the waiting time until the next
time a new fare is started.
Note:
In order for this function to work well it is necessary to program several questions in block number 62 because this is the block that is loaded when the forfait is used
according to the following list:
No / Yes
Q13 = 0 : disable key K1
Q21 = 0 : no extra-charge n. 1
Q23 = 0 : no extra-charge n. 2
Q25 = 0 : no extra-charge n. 3
Q27 = 0 : no extra-charge n. 4
Q34 = Yes : disable distance measurement in Stopped
Q36 = Yes : disable distance measurement in Hired
Q37 = Yes : disable waiting-time measurement in Hired
Q40 = 0 : disable Night-time
Q41 = 0 : disable Night-time
Q52 = 0 : disable Holiday-time
Q53 = 0 : disable Holiday-time
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
342 Available for any possible software extension
343 Must the black trips saving operation be avoided? No / Yes
344 Must the cash trips saving operation be avoided? No / Yes
345 Must the Credit trips saving operation be avoided? No / Yes
346 Must the Power off saving operation be avoided? No / Yes
347 Must the shifts saving operation be avoided? No / Yes
from Q 348 / Available for custom parameters / to Q 370
CONNECTION TO THE DISPATCHER
371 Transmit undefined status to dispatcher? - Transmit an undefined status to the dispatcher? The allowed answer is either: 0 (No: don't transmit) or: 1 (Yes: transmit). No / Yes
372 Transmit ForHire status to dispatcher? - Transmit the ForHire status to the dispatcher? The allowed answer is either: 0 (No: don't transmit) or: 1 (Yes: transmit). No / Yes
373 Transmit Stopped status to dispatcher? - Transmit the Stopped status to the dispatcher? The allowed answer is either: 0 (No: don't transmit) or: 1 (Yes: transmit). No / Yes
374 Transmit Hired status to dispatcher? - Transmit the Hired status to the dispatcher? The allowed answer is either: 0 (No: don't transmit) or: 1 (Yes: transmit). No / Yes
375 Block taximeter if driver ID is 0? - Should the taximeter be blocked if the identification number of the driver is 0?
The allowed answer is either: 0 (No: don't block) or: 1 (Yes: block).
No / Yes
376 Assign ID 9999999 if driver ID is 0? - Should driver ID 9999999 be assigned if the identification number of the driver is 0?
The allowed answer is either: 0 (No: don't assign) or: 1 (Yes: assign).
No / Yes
377 If driver = 0, must the meter show "Close" in For Hire mode? No / Yes
378 Requesting Ticket the taximeter powers on the Printer? - If Yes, after printing, the taximeter powers off the printer No / Yes
379 Define if thermal printer width is 44 mm or 57 mm No / Yes
380 Must blank lines printing be avoided? No / Yes
381 Is thermal printer in usage? No / Yes
382 Where the thermal printer is connected? (0 = Com 1 1 = Com 2) No / Yes
383 Enable taximeter-dispatcher connection? - Should the possibility to connect the taximeter with a dispatcher be enabled?
The allowed answer is either: 0 (No: disable) or: 1 (Yes: enable).
No / Yes
384 Dispatcher is connected to COM1 or COM2? - Is the dispatcher connected to COM1 or to COM2 ? See also Q.383 and Q.385 to Q.387.
The allowed answer is either: 0 (No: COM1) or: 1 (Yes: COM2).
0= COM1 1=
COM2
385 COM1 protocol is Digitax or custom? - The protocol used for data-transmission on COM1 is the Digitax protocol or a custom protocol?
See also Q.383, Q.384 and Q.386, Q.387. The allowed answer is either: 0 (No: Digitax protocol) or: 1 (Yes: custom protocol).
0= Digitax
1= Custom
386 COM2 protocol is Digitax or custom? - The protocol used for data-transmission on COM2 is the Digitax protocol or a custom protocol? 0= Digitax
To Next Page
Loading...
Need help?
General
