Dimplex BF36DX - User Manual

Other manuals for Dimplex BF36DX

Installation Guide10 pages

Questions and Answers

G
ghickmanSep 10, 2025
What to do if my Dimplex Indoor Fireplace does not turn on with remote control?
- A
  ajohnsonSep 10, 2025
  If your Dimplex Indoor Fireplace does not turn on with the remote control, ensure proper operation. Also, the remote control might not be initialized to the fireplace, so initialize it. If that doesn't work, the remote control might be defective. Install a new battery into the remote control and reinitialize the remote where necessary. Lastly, a defective Remote Control Receiver could be the problem, so replace it.
B
Brittney ReynoldsAug 23, 2025
What to do if my Dimplex Indoor Fireplace heater is not turning off?
- J
  Jodi GilbertAug 23, 2025
  If your Dimplex Indoor Fireplace heater is not turning off, it might be due to improper operation of the unit. It can also be caused by improper operation of the Thermostat/Wall Controls (if applicable). Another cause may be a defective heater on/off switch, so consider replacing it. Finally, the heater assembly could be defective and needs replacement.
J
Jaclyn PetersAug 25, 2025
Why is my Dimplex Indoor Fireplace heater turning off after a couple of minutes?
- K
  Kevin JamesAug 25, 2025
  The Dimplex Indoor Fireplace heater might be turning off after a couple of minutes due to a build-up of dirt/dust in the heater assembly. Ensure that exterior intake louvers and the firebox cavity are free of dirt and dust. Alternatively, the heater assembly could be defective. Replace the heater motor if it's not running when heat is activated, or replace the heater elements if the motor is running but heat isn't coming out.
C
cynthia53Aug 26, 2025
Why is my Dimplex Indoor Fireplace heater not turning on?
- D
  Debra MorrisAug 26, 2025
  If the heater on your Dimplex Indoor Fireplace isn't turning on, it could be due to several reasons. It might be due to improper operation. Check for loose wiring in the unit. A defective heater switch or a defective remote control receiver (if applicable) could also be the cause. In such cases, replace the heater switch or the remote control receiver kit.
L
Lisa HarrisAug 28, 2025
What to do if my Dimplex Indoor Fireplace is making excessive noise with the heater on?
- M
  Morgan CooleyAug 28, 2025
  If your Dimplex Indoor Fireplace is making excessive noise when the heater is on, it could be due to a dirty blower assembly. Make sure that the exterior intake louvers and firebox cavity are free of dirt and dust. Another potential cause is a defective heater motor, which would need to be replaced.
M
Mark McguireAug 29, 2025
Why does my Dimplex Indoor Fireplace unit turn on and off by itself?
- W
  williamwilliamsAug 29, 2025
  Your Dimplex Indoor Fireplace might be turning on and off by itself because the remote control has a similar frequency to other remotes in the area; try replacing the remote control. Radio frequency disturbance from outside sources could also be the reason; in this case, replace the remote control and the Remote Control Receiver Kit, where necessary. A defective Remote Control Receiver could also be the culprit; replace the Remote Control Receiver.
N
Natasha LawrenceSep 18, 2025
How to fix light leaking around the log set on Dimplex Indoor Fireplace?
- A
  Andrew TurnerSep 18, 2025
  To fix light leaking around the log set of your Dimplex Indoor Fireplace, check the log set for proper fit, as it may not be positioned correctly.
B
Brian BurnsSep 12, 2025
Why is the heating element glowing red in my Dimplex Indoor Fireplace?
- T
  Tracy BrownSep 12, 2025
  Small glowing sections of the heating element in your Dimplex Indoor Fireplace are considered normal. However, if larger glowing sections are causing the heater to trip the thermal cutout, unplug the unit, discontinue use, and replace the heater elements.
K
Kathleen MilesSep 8, 2025
How to fix Dimplex Indoor Fireplace heater fan that runs continuously?
- P
  pboyleSep 8, 2025
  If the heater fan in your Dimplex Indoor Fireplace runs continuously, the heater on/off switch is likely defective and needs to be replaced.
S
shannonvaldezSep 5, 2025
What to do if Dimplex Indoor Fireplace does not turn on manually?
- P
  Pamela SextonSep 5, 2025
  If your Dimplex Indoor Fireplace does not turn on manually, it might be due to improper operation. There might be no incoming voltage from the electrical wall socket/Breaker Panel, so check the Fuse/Breaker Panel. Another reason may be loose wiring, so check wiring connections. It could also be a defective On/Off Switch, a defective Heater Switch, or a defective Remote Control Receiver (if applicable), so replace them if needed.

Summary

Operation

Manual Controls

Explains how to operate the fireplace using its built-in manual switches for flame and heat.

Remote Control Operation

Covers remote control features, initialization procedures, and sequential usage for fireplace control.

Wall Mounted Controls

Details the functionality of optional wall-mounted switches and thermostats for controlling the fireplace.

Maintenance Procedures

Light Bulb Replacement

Step-by-step guide for safely replacing burnt-out light bulbs within the fireplace unit.

Glass Cleaning

Instructions for cleaning the fireplace's glass door to remove smudges and water spots.

Wiring Diagrams

Mod 0-B Wiring

Electrical schematics illustrating the wiring configurations for Model 0-B.

Mod C-E Wiring

Electrical schematics illustrating the wiring configurations for Model C-E.

Switch and Motor Replacement

Switch Replacement

Detailed steps for replacing the main power and heater on/off switches.

Flicker Motor;Rod Replacement

Instructions for removing and replacing the flicker motor and rod assembly.

Heater Element Replacement

Guide for safely removing and installing the unit's heating elements.

Component Replacements

Blower Motor;Blower Replacement

Steps to remove and install the blower motor assembly.

Temperature Limit Switch Replacement

Guide for locating and replacing the thermal cutout safety switch.

Remote Control Receiver Replacement

Steps to safely remove and install the remote control receiver unit.

Advanced Configuration

Remote Control Receiver Diagrams

Visual representations of different remote control receiver circuit board layouts.

Input Voltage Changing

Instructions for converting the fireplace to different voltage configurations (120V/208V/240V).

Voltage Conversion Procedures

Rewiring for 120 V with Remote Controls

Detailed steps to rewire the unit for 120V operation with remote controls.

Rewiring for 120 V without Remote Controls

Detailed steps to rewire the unit for 120V operation without remote controls.

Dimplex BF36DX Specifications

General

Model	BF36DX
Type	Electric Fireplace
Power Source	Electric
Style	Traditional
Remote Control	Yes
Flame Effect	Yes
Volts	120V
Heater	Yes
Fireplace Style	Insert
Fuel Type	Electric
Flame Brightness Adjustment	Yes
Heat Settings	High/Low
Thermostat	Yes
Timer	Yes
Log Set Included	Yes
Width	36 in
Wattage	1500W
BTUs	5100 BTUs
Installation	Wall-mounted
Heating Capacity	400 sq ft
Power Consumption	1500W