Why is my Dimplex DF2426 making excessive noise when the heater is on?
If there is excessive noise when the heater is on in your Dimplex Indoor Fireplace, it could be due to a dirty Heater Assembly. Ensure that the exterior intake louvers and firebox cavity are free of dirt and dust. Another possibility is a defective Heater Assembly, which would need to be replaced.
Why is the flame not bright or visible in my Dimplex DF2426 Indoor Fireplace?
If the flame in your Dimplex Indoor Fireplace is not bright or visible, it could be due to burnt-out light bulbs, which you should replace. Another cause might be loose wiring, so check the wiring connections. Finally, a defective Light Harness could also be the problem, requiring replacement.
Why does the heater fan run continuously in my Dimplex DF2426 Indoor Fireplace?
If the heater fan in your Dimplex Indoor Fireplace runs continuously, it could be due to a defective Heater Switch, Thermostat, or Heater Assembly, any of which would need to be replaced.
Why is the flame frozen in my Dimplex DF2426?
If the flame is frozen in your Dimplex Indoor Fireplace, it could be due to a defective Flicker Motor, which would need to be replaced. Another possibility is loose wiring, so check the wiring connections.
Why is my Dimplex DF2426 Indoor Fireplace making grinding noises with the heater off?
If you hear grinding or excessive noise from your Dimplex Indoor Fireplace when the heater is off, it could be that the flicker rod is hitting or rubbing against internal components. Ensure the rod is straight and mounted properly in the bracket, spinning freely away from other components. Replace it if necessary. Alternatively, it could be a defective Flicker Motor, which would need to be replaced.
What causes flame shutter in Dimplex Indoor Fireplace?
If you are experiencing a flame shutter issue with your Dimplex Indoor Fireplace, it is likely due to a defective Flicker Motor, which will need to be replaced.
Why is the log set dim in my Dimplex Indoor Fireplace BF9000?
If the log set in your Dimplex Indoor Fireplace (BF9000 model) is dim and not glowing, check the wiring connections for any looseness. It could also be due to a defective LED Log Driver Board or a defective Log Set Assembly, both of which would need to be replaced.
Why does the circuit breaker trip when I turn on my Dimplex DF2426?
If the circuit breaker trips or a fuse blows when you turn on your Dimplex Indoor Fireplace, it could be due to a short in the unit's wiring. In this case, trace the wiring in the unit. Alternatively, it might be that additional appliances are drawing too much current on the same circuit. Try plugging the fireplace into another outlet or installing it on a dedicated 15 amp circuit.
Why is the log set dim and not glowing on my Dimplex BF9000 Indoor Fireplace?
If the log set is dim and not glowing on your BF9000 Dimplex Indoor Fireplace, it could be due to loose wiring, which requires checking the wiring connections. It may also be caused by a defective LED Log Driver Board or a defective Log Set Assembly, both of which would need replacement.
Why is the flame not bright or not visible on my Dimplex Indoor Fireplace?
If the flame on your Dimplex Indoor Fireplace is not bright or not visible, it could be due to burnt-out light bulbs, which need replacement. Another possible cause is loose wiring, so check the wiring connections. Finally, a defective Light Harness or LED Light Assembly may be the issue, requiring replacement.
General| Model | DF2426 |
|---|---|
| Product Type | Electric Fireplace |
| Style | Traditional |
| Fuel Type | Electric |
| Voltage | 120V |
| Wattage | 1500W |
| Heating Area | 400 sq. ft. |
| Remote Control | Yes |
| Adjustable Thermostat | Yes |
| Material | Metal and Glass |
To Next Page
