How to fix switch 2 input will not activate relay on DKS Intercom System?
If switch 2 input will not activate the relay on your DKS Intercom System, reprogram switch input 2 to activate the relay.
What to do if my DKS Entry system will not answer when called?
If your DKS Entry system isn't answering when called, check these items: * Ensure the ring pin is installed. * Verify the number of rings to answer isn't set too high; reprogram if needed. * Check for a bad phone line or insufficient ring voltage.
Why relay activates but gate operator will not open on DKS 1803 Intercom System?
If the relay activates but the gate operator does not open on your DKS Intercom System, try the following: * Reprogram the relay strike time for a longer duration. * Check the wiring to the gate operator. * Inspect the gate operator itself.
Why touch-tone 9 will not activate relay on my DKS 1803 Intercom System?
If touch-tone 9 will not activate the relay on your DKS Intercom System, try re-programming the tone-open number to 9. If the resident phone emits a short pulse instead of a long tone, press 9 twice in rapid succession. You can also try using another phone that is known to work, or lower the speaker volume and readjust the feedback.
What to do if the relay activates but the gate operator will not open on my DKS Entry phone?
If the relay activates but the gate operator doesn't open on your DKS Entry phone, consider these steps: * Re-program the relay strike time for a longer period. * Check the wiring to the gate operator. * Check the gate operator itself.
What to do if FIVE-digit entry codes will not work on my DKS Entry phone?
If FIVE-digit entry codes aren't working on your DKS Entry phone, ensure that: * You are pressing “#” first. * The entry code may be time zone restricted. Reprogram the time zone or disable it.
Why four-digit entry codes will not work on my DKS 1803 Intercom System?
If four-digit entry codes are not working on your DKS Intercom System, make sure you are pressing # first. The entry code might also be time zone restricted, so reprogram the time zone or turn it off. The entry code may have also been a flash code that is no longer valid.
What causes buzz or noise on the phone line with my DKS Intercom System?
If your DKS Intercom System is emitting a buzz or noise on the phone line, try these checks: 1. Disconnect the phone line from the system and test it with a handset to determine if the noise originates from the phone line itself. 2. Inspect for any shorts to ground behind the circuit board. 3. Check for pinched wires near the door hinge. 4. Look for a 16-volt power or phone line shorted to ground. 5. Ensure that phone wires are twisted and that the correct type of phone wire is used, especially for outdoor or underground applications. 6. Verify that all wires, including the speaker and keypad, are isolated from ground. 7. Confirm that the cabinet is properly grounded and that the case ground (terminal 3) is not used as a low voltage common. 8. Check for excessive voltage drop on t...
Why does the door strike lock on my DKS Intercom System?
If the door strike on your DKS Intercom System locks on, it could be due to: * Excessive voltage drop on the 16 VAC line. * Using a transformer with too low VA rating. * Relay strike time programmed for too long.
Why does my DKS Intercom System emit a long tone and cancels programming?
If your DKS Intercom System emits a long tone and cancels programming, it may be due to: * Pausing too long between button presses. * Forgetting to press the * key before programming.
FCC compliance information for digital devices in the US.
Canadian compliance for telecommunications equipment.
General guidelines and steps for installing the telephone entry system.
Instructions for surface mounting 1803, 1810, and 1808 models.
Instructions for semi-flush mounting units using a recess box.
Details for flush mounting units into walls with specific kits.
Specifications for the rough-in box used in flush mounting.
Information on the trim ring for flush mount installations.
Instructions for installing the memory chip into the circuit board.
Guidance on installing an optional postal lock for mail carrier access.
Introduction to wiring and adjustment procedures.
Details on adjusting various settings on the control circuit board.
Visual representation of system wiring connections.
Explanation of the purpose of each terminal on the main board.
Procedures for adjusting speaker, microphone, and other settings.
Overview of programming via keypad and remote telephone.
Basic programming steps including Master Code and system settings.
Procedures for entering and managing phone numbers and directory codes.
Setting up and managing four-digit and five-digit entry codes.
Programming time-based functions like time clock and time zones.
General guidance for guests and residents using the system.
Operations for system administrators, including remote access.
Instructions for switch input, talk time, line sharing, and PBX connection.
List of replaceable parts and their part numbers.
Guide to diagnosing and resolving common system issues.
Descriptions and part numbers for optional accessories.
Tables for recording system programming and resident data.
General| Brand | DKS |
|---|---|
| Model | 1803 |
| Category | Intercom System |
| Language | English |
To Next Page
