DMP XTL - LED Operation; Backlit Logo; Reset Button; Description

XTL/XTLC Installation Guide Digital Monitoring Products
5
InstallatIon
LED Operation
7.1 Backlit Logo
ThebacklitlogoindicatesthePowerandArmedstatusofthepanel.Dependingontheoperation,theLED
displaysinRedorGreenaslistedinthetable.
Color and Activity Operation
GreenSteady PanelDisarmed,PrimaryPowerOK,BatteryOK
GreenBlinking PanelDisarmed,PrimaryPowerOK,BatteryFault
NoLight PanelDisarmed,PrimaryPowerFault,BatteryOK
Red Steady PanelArmed,PrimaryPowerOK,BatteryOK
Red/GreenAlternate PanelArmed,PrimaryPowerOK,BatteryFault
RedBlinking PanelArmed,PrimaryPowerFault,BatteryOK
Reset Button
8.1 Description
Theresetbutton(S1)islocatedontherightsideofthecircuitboardandisusedtoresettheXTL/XTLC
microprocessor. To reset the panel prior to reprogramming, press the reset button without powering down
thesystem.Afterresettingthepanel,beginprogrammingwithin30minutes.Ifyouwaitlongerthan30
minutes, you must reset the panel again.
Programming Connection
9.1 Programming Connection
Alocking4-pinheader(PROG)isprovidedtoconnectakeypadwhenusingaDMPModel330Programming
Cable.Thisprovidesaquickandeasyconnectionforprogrammingthepanel.Afterprogrammingis
complete,removethekeypad.
Installing the 738Z
Toconnectthewiringofthe738ZtothePROGheaderofthepanel,useaPC-0140ConnectorAssembly
(includedwiththe738Z)forconnectionofaModel300harness.The738Zonlyoperateswhenprimarypower
is present.
Note:ThePROGheaderisnotintendedtoprovideaKeypadDataBusconnection.Theprogrammingkeypad
isoperationalonlywhenprimarypowerisappliedtotheXTL/XTLC.
On-Board 1100 Series Wireless
10.1 Wireless Antenna
TheXTL/XTLCWirelessAntennaisintegratedintothecircuitboard.Thebuilt-inwirelessreceiveroperates
withDMP1100Seriestransmitters.Seesection3.1foralistofaccessorydevices.
10.2 Wireless LED Operation
Green (TX):ThegreenLEDasheseverytimethereceivertransmits(32timespersecond).Ifthepanel
isreset,orthepanelispoweredoff,thegreenLEDisoff.Undernormaloperation,thegreenLEDashes
constantly with no interruption or change.
Yellow (RX):TheyellowLEDasheseverytimetheXTL/XTLCreceivesamessagefromaprogrammed
wirelesstransmitter.Whenamessageissentbyatransmitter,typicallybypressingorreleasingthetamper
switch,theyellowLEDshouldashindicatingthatthepanelreceivedamessagefromthetransmitter.
IftheLEDneverashes,thetransmitterisnotgettingthroughtothepanel.Thiscouldbebecauseofa
misprogrammedserialnumberorthetransmitteristoofaraway.Undernormaloperation,theyellow
LEDashesateverytripofeverywirelesstransmitterandwhenthetransmittersperformtheirperiodic
check-in.ItisnotunusualforthisLEDtostayoffformanyminutesatatimewhennotransmittersare
communicating.