Dolmar PS-352 TLC - User Manual

Questions and Answers

L
lori73Aug 18, 2025
Why does my Dolmar Chainsaw engine not start?
- A
  Ariel EscobarAug 18, 2025
  If your Dolmar Chainsaw engine won't start, there are several possible causes: * A spark plug malfunction: Check the spark plug. * The fuel tank is empty: Fill the fuel tank. * A fuel supply problem: Check whether the fuel filter is not clogged. * Tool malfunction: Ask your local authorized service center for repair.
A
Anne TranAug 20, 2025
Why Dolmar PS-352 TLC engine does not start?
- R
  Rhonda StoneAug 20, 2025
  Several factors can prevent your Dolmar Chainsaw engine from starting. It could be due to a spark plug malfunction, which requires checking the spark plug. Another reason might be an empty fuel tank, so ensure you fill it. Also, a clogged fuel filter can cause fuel supply problems. If none of these resolves the issue, it might be a tool malfunction.
C
clintonhuntAug 23, 2025
What to do if there is no oil on the Dolmar Chainsaw chain?
- P
  Peter FosterAug 23, 2025
  If there's no oil on the saw chain of your Dolmar Chainsaw, the possible causes are: * The oil tank is empty: Fill the oil tank. * The oil guide groove is dirty: Clean the groove. * Oil delivery is not adjusted properly: Adjust the amount of oil delivery. * Oil pump malfunction: Ask your local authorized service center for repair.
R
Randall PerryAug 25, 2025
How to fix Dolmar PS-352 TLC chain that does not run?
- M
  Morgan MillerAug 26, 2025
  If the Dolmar Chainsaw chain does not run, it is likely that the chain brake is engaged. Release the chain brake.
E
Elizabeth DiazAug 27, 2025
What to do if Dolmar PS-352 TLC has insufficient performance?
- J
  James TurnerAug 28, 2025
  If your Dolmar Chainsaw isn't performing well, start by checking the air cleaner; it might be dirty and need cleaning or replacing. Also, a dirty cylinder space can cause this issue, so clean it. Low environmental temperatures can also affect performance; adjust the carburetor shutter setting accordingly.
S
scottcynthiaAug 30, 2025
What to do if Dolmar PS-352 TLC Chainsaw has no oil on the saw chain?
- V
  victoria85Aug 30, 2025
  If there's no oil on the saw chain of your Dolmar Chainsaw, first check if the oil tank is empty and fill it if needed. Also, a dirty oil guide groove can cause this, so clean the groove. Check the oil delivery if it is not adjusted properly and adjust the amount of oil delivery.
P
Patricia ThompsonSep 1, 2025
Why is my Dolmar PS-352 TLC performance insufficient?
- V
  vazquezcarlSep 1, 2025
  If your Dolmar Chainsaw is not performing well, it could be due to: * A dirty air cleaner: Clean the air cleaner or replace it if necessary. * A dirty cylinder space: Clean the cylinder space. * Very low environment temperature: Change the shutter setting of the carburetor. See section “Prevention from carburetor icing”.
S
Scott SalasSep 3, 2025
What to do if the Dolmar PS-352 TLC chain does not stop with the brake?
- A
  Alicia NelsonSep 4, 2025
  If the Dolmar Chainsaw chain does not stop even when the chain brake is activated, stop using the tool immediately, and ask your local authorized service center for repair, because the brake band may be worn down.
S
Steven TrujilloSep 6, 2025
Why does my Dolmar PS-352 TLC Chainsaw vibrate abnormally?
- W
  William SaundersSep 6, 2025
  If your Dolmar Chainsaw vibrates abnormally, it might be due to: * Loose guide bar or saw chain: Adjust the guide bar and saw chain tension. * Tool malfunction: Stop using the tool immediately, and ask your local authorized service center for repair.
M
Miss Jennifer KingSep 8, 2025
What to do if the Dolmar Chainsaw chain does not stop when engine is idle?
- R
  Rachel JacobsSep 8, 2025
  If the Dolmar Chainsaw chain does not stop when the engine is idle, it could be due to: * Idle speed being too high: Correct the idle speed. * Clutch defect: Stop using the tool immediately, and ask your local authorized service center for repair.