ES 200
ES 200
ES 200-2D
ES 200
ES 200
ES 200-2D
DORMA DORMA
Easy Easy
Recycling and disposal
Both the ES 200 , the ES 200, the
ES 200-2D and their packing mainly consist of
recyclable raw material.
The ES 200 , the ES 200, the ES 200-2D
and the respective accessories must not be
disposed of as domestic waste.
Please ensure that the old appliance and the
respective accessories (if available) are properly
disposed of.
Please abide by the prevailing national statutory provisions.
Safety during mounting
·The working area has to be secured against
unauthorised access from other people. Falling items
or tools might cause injuries.
·The ES 200 , the ES 200 and the ES 200-2D
have to be secured against water and other liquids.
·In any case, the way of mounting and the mounting
equipment, like for example screws and wall plugs,
have to be adequate with regard to the structural
conditions (steel structure, wood, concrete etc.).
·The mounting of the ES 200 , the ES 200 and
the ES 200-2D described herein are only an example.
Structural or local conditions, available tools or other
conditions might suggest a different approach.
·Following the successful installation of the system, the
settings and the proper function of the ES 200 ,
the ES 200 or the ES 200-2D and the safety
equipment have to be checked.
·Only specially qualified staff may open the power
supply housing.
·Disconnect the ES 200 , the ES 200 or the
ES 200-2D from power supply (de-energise the
system) before removing the cover of the power supply
housing. Remove mains plug or switch off fuse (with
permanent power supply).
·Always pull at the plug and never at the cable when
unplugging the power supply.
Safety during commissioning
·The protective earth conductor has to be connected.
·The safety sensors are to be connected (see
commissioning instructions).
·The operator and the active panels are properly linked.
·The end stops are adjusted so that the sliding panels
meet the end stops when the system is adjusted to its
maximum opening width
·Furthermore the sealing profiles of the active panels
and the passive panels must not collide while the door
is closed
·Separately supplied components such as the program
switch, the EMERGENCY OFF pushbutton and
activators (radar motion detectors, NIGHT-/BANK key
switches) have to be mounted and connected.
·Ensure that the door leaves run smoothly
·The rechargeable battery pack has been installed
(optional).
Inspection and system approval
Before the first commissioning and depending on
requirements, however, at least once a year, the
ES 200 , the ES 200 and the ES 200-2D have to be
inspected by a properly qualified technician and serviced if
required.
A person trained by DORMA has to perform the inspection
and approve the system with the aid of the inspection book.
The respective results have to be documented in accordance
with DIN 18650-2 and the facility operator has to keep
these documents for at least one year.
We would recommend taking out a maintenance agreement
with DORMA.
Easy
Easy
Easy
Easy
Easy
Easy
Easy
Briefing:
Following the adjustment, commissioning and functional
testing of the door system, the operating instructions have
to be handed over to the facility operator and a briefing has
to be made.
Behaviour of door system during varying weather conditions
The safety sensors (infrared light curtains) are designed to
safeguard the passage area. When it comes to adjusting the
sensitivity of the sensors, the protection of people always
has top priority. From time to time, changing climatic
conditions (such as rain or snow), flying leaves or direct
sunlight (reflected by certain floor finishes) may
accidentally trigger the sensors. As soon as the light
curtains have been triggered, the door may remain open for
up to one minute – as required by a certain standard. This is
only a standard procedure with the only purpose to protect
the users of the door system.Maintenance
The system has to be de-energised (disconnected from
power supply) before performing any kind of maintenance
work.
Remove the power plug or switch off the fuse (with
permanent power supply).
Care
The system has to be de-energised (disconnected from
power supply) before cleaning the system. Remove the
power plug or switch off the fuse (with permanent power
supply).
You may clean the ES 200 , the ES 200 or the ES
200-2D with a damp cloth and standard commercial
detergents.
You should not use scouring agents for cleaning purposes as
they might damage the surface finish.
Ensure that no water or other liquids drop on or into the
ES 200 , the ES 200 or the ES 200-2D.
Never stick metal objects into the openings of the
ES 200 , the ES 200 or the ES 200-2D otherwise you
might sustain an electric shock.
Wear
The following wear parts must be checked in regular
intervals and replaced if required in order to ensure the
smooth function of the unit.
• Track rollers: every 2 years
• Rubber end stops: at every service check
• Track rail: every 5 years
• Toothed belt: every 1,000,000 opening/closing
cycle
• Floor guides: at every service check
• Brushes (optional)
Only use original spare parts.
Easy
Easy
Easy
Main
closing edge
Secondary
closing edge
1. For your safety
This documentation contains important information
regarding the mounting and the safe operation of the door
system.
Please read these instructions carefully before using the
ES 200 , the ES 200 or the ES 200-2D.
It is important for your personal safety to abide by all
enclosed instructions.
An incorrectly performed installation might cause serious
injuries.
Using control elements, making adjustments or performing
procedures that are not described in this documentation
might cause electric shocks, danger caused by electric
voltage/current and/or danger due to mechanical incidents.
Please keep these documents for further reference and hand
them over to the person in charge in case the system is
transferred to another party.
Explanation of symbols
WARNING This symbol underlines important
information that may facilitate your work.
It warns you of possible system damage
and explains how to avoid this damage.
It indicates dangers that might cause
personal or material damage or even kill
people.
Intended application
The ES 200 is only designed to open and close interior
sliding doors with an admissible door panel weight up to
1 x 100 kg or 2 x 85 kg.
The ES 200 is neither suitable for application in
escape routes, nor at fire doors (fire and smoke doors) nor at
exterior doors.
The ES 200 is only designed to open and close interior
sliding doors with an admissible door panel weight up to
1 x 200 kg or 2 x 160 kg.
The ES 200 is neither suitable for application in escape
routes, nor at fire doors (fire and smoke doors) nor at
exterior doors.
ES 200-2D is only designed to open and close interior
sliding doors with an admissible door panel weight up to
1x 150 kg or 2 x 130 kg.
The ES 200-2D is suitable for application in escape route.
The ES 200-2D is neither suitable for application at fire
doors (fire and smoke doors) nor at exterior doors.
The maximum cable length for external components must
not exceed 30 m.
Limitation of liability
The ES 200 , the ES 200 and the ES 200-2D may only
be used according to its specified intended application. The
DORMA GmnH + Co. KG will not accept any liability for
damage resulting from unauthorised modifications of the
ES 200 , the ES 200 and the ES 200-2D.
Furthermore components/accessories that have not been
approved by DORMA are exempted from liability.
Safety instructions
Work on electrical equipment may only be performed
by properly qualified staff (electricians).
·Do not allow children to play with the ES 200 ,
the ES 200, the ES 200-2D or its adjustment and
control devices.
·Keep remote controls out of reach of children.
·Never stick metal objects into the openings of the
ES 200 , the ES 200 or the ES 200-2D;
otherwise you might sustain an electric shock.
·If the ES 200 , the ES 200 or the ES 200-2D are
mounted onto a metal door leaf, you have to earth
(ground) the door leaf properly.
·Glass door leaves have to be made of safety glass.
Easy
Easy
Easy
Easy
Easy
Easy
Easy
Easy
Important technical data
ES 200 , ES 200 ES 200-2D
·Power supply 230 V
·Fuse (by others) 16 A
·Operating noise < 70 dB(A)
Standards, laws, codes and regulations
·The latest versions of the common and country-
specific standards, laws, codes and regulations have to
be observed.
DIN 18650 (German Industrial Standard)
During the planning of the door system, the manufacturer
(the person installing the system) and the
commissioner/facility operator have to perform an individual
risk assessment (together).
Please refer to our homepage and consider
the provided “risk assessment form” under PRODUCT for
further assistance when performing your individual risk
assessment.
Danger spots at closing edges
Automatic doors might cause hazards by crushing,
shearing, hitting and drawing-in at the different
closing edges.
Residual risk
Depending on the structural conditions, the prevailing door
version and the available safety equipment, residual risks
such as crushing and hitting (with a limited force) cannot be
excluded.
Easy
·Admissible humidity 93% relative humidity
non condensing
·admissible temperature: -20°C - +60°C
www.dorma.com
To Next Page
Loading...
