Dorma EM User Manual

Contenu de la boite
1/2
DORMA
Bandeau EM
2 x 300 Kg sans report
snoitacifidom ed evresér suoS
Pose-Rac_Bandeau_2x300_SR
Support ventouse
Bouchon d’extrémite
Cache fil Support ventouse
X 2
X 2
Support Poignée
Cache Poignée
Bouchon d’extrémite
X 3
Vis bouchon d’extrémité (10)
vis de renfort poignées (7)
X 1
Accessoires en option : Renforts et poignées (nous consulter)
Renfort sans poignée
(pour corps ventouse
ou pour poignée)
Renfort avec poignée
(pour poignée)
Conseils de pose
Vérifiez que la porte s'ouvre bien, ne frotte pas au sol.
N'hésitez pas à déposer la porte si ceci est plus pratique
(par exemple pour les bouchons d'extrémité)
Les bouchons d'extrémité ont une épaisseur de 3mm.
Tenez en compte pour la découpe à longueur.
Posez les caches de finition.
Utilisez des vis M5 ou M6, têtes rondes, selon le support.
Intervalle conseillé 200 mm.
GB
Optional Accessories: Reinforcements and handles
Reinforcement
without handle
Reinforcement
with handle
GB
Package Contents
GB
Tips for laying
Make sure the door opens it, do not touch the ground
Please leave the door if this is more convenient
(Eg for end caps)
The end caps have a thickness of 3mm.
Keep this in mind when cutting to length
Put the finishing covers.
Use M5 or M6, round heads, as the media.
Interval advised 200 mm.
F
F
F
Support ventouse
Support poignée
Support magnet
Support handle
Ne posez les vis de renfort poignée (7) qu'à la fin des
travaux. Elles sont indémontables.
Put the screw handle reinforcement (7) only at
the end of the work. They are tamperproof.
Screw handle
reinforcement
Vis de renfort poignée
DORMA Sécurité Temps Accès S.A.S . Europarc . 94046 Créteil . Tél: 01.41.94.26.00
3 7 0 0 0 0 0 8 1 5 2 0 0 Version : 18/02/2011

Dorma EM Specifications

General

Brand	Dorma
Model	EM
Category	Door Opening System
Language	English

Summary

Box Contents

Handle Support

Component for supporting the handle in the door.

End Cap

Component used to cap the ends of the door.

Handle Cover

Component that covers the handle.

Suction Cup Support

Support component for the suction cup.

End Cap Screws

Screws provided for fixing the end caps.

Handle Reinforcement Screws

Screws for handle reinforcement, tamperproof.

Suction Cup Wire Cover

Cover for the wires of the suction cup support.

Optional Accessories

Reinforcement Without Handle

Optional reinforcement component for the suction cup body or handle.

Reinforcement With Handle

Optional reinforcement component for the handle.

Installation Tips

Door Operation Check

Verify door opens freely without touching the ground.

Door Removal Recommendation

Advise removing the door for easier installation of components like end caps.

End Cap Thickness Consideration

Note end caps are 3mm thick, consider for length cutting.

Screw Type and Interval

Use M5 or M6 round head screws, advised interval 200mm.

Handle Reinforcement Screw Timing

Install handle reinforcement screws at the end; they are tamperproof.

Finishing Covers

Install the final finishing covers.

Electrical Connection

Power Supply Requirements

Use a stabilized DC power supply, 12 or 24 VDC, 1A minimum.

Factory Pre-wiring

Product is factory pre-wired for 12 V DC.

Voltage Selection 12V

Factory setting for 12V operation, shows wiring diagram.

Voltage Selection 24V

Procedure for 24V operation by connecting red and white wires.

Report Information

Locking Information Report

This model does not have a locked information report contact.

Specifications

Length

The total length of the product is 2500mm.

Materials

The product is constructed from extruded aluminum.

Holding Force

The maximum holding force is 600 DaN.

Power Consumption

Consumes 1.0A at 12VDC or 0.5A at 24VDC.

Protection Rating

The product has an IP42 protection rating.