Dorma ES 200 Easy - User Manual

DORMA •
ES 200 Easy
ES 200
ES 200-20
ES 200 C048/ DAC 300
~
DORMA
1. Commissioning
1. Commissioning
1.1 Please note:
Work on electrical equipment may only be performed
by properly qualified electricians.
Power supply (by others) with 16 A fuse protection
must be available.
Power cord must be double-insulated, for example:
NYM. Do not use flat webbed house wires!
The maximum cable length of the external
components must not exceed 30 m.
1.2 Basic requirements:
• The operator is fully assembled.
• The protective earth (PE) is connected.
• The safety sensors are connected.
• Components supplied separately, such as
program switches, activators, radar motion
detectors, Night-/Sank keyswitches and
EMERGENCY OFF pushbuttons are installed
and connected .
• The end stops are adjusted so that both active
panels touch the end stops when the panels
have reached maximum opening width.
• When the door is closed, the active and the
passive door panel must not collide with the
sealing profiles.
• The door has to run smoothly. Check the length
of the connection screws of the toothed belt
Ij\ and replace the screws if necessary.
Lll Update (small motor)
The ES 200 control unit can be installed as a
replacement for older systems with GR 63x25 motors.
However, a special cable for the incremental encoder
with a pulse devider is required.
The following procedure has to be observed:
- Install hardware.
- Set program switch to "OFF" and activate the
EMERGENCY OFF pushbutton.
- Reset system to original settings (factory settings):
Press and hold service key, switch on power supply.
- Release the service key as soon as the 8 on the
seven-segment display blinks twice.
- Adjust the GR 63x25 Motor via the pushbuttons on
the basic module (b = 0) or via PDA.
- Unatch the EMERGENCY OFF pushbutton.
- Perform a learning cycle.
A Safeguarding of door:
The safety measures to safeguard the doors must
be made in accordance with the local (country-
specific) regulations.
Where sliding doors shall be operated in Germany
according to DIN 18650 (German Industrial
Standard), the specifications stated in this
industrial standard must be observed.
See: WN 057015 45-5-32
1.3 First Commissioning
1.3.1 Open the sliding panels half way.
1.3.2 ES200 Easy:
• Set program switch to AUTOMATIC
ES200 I ES200-2D:
• Set program switch to OFF
1.3.3 Unlatch the EMERGENCY OFF pushbutton
and bridge the light barriers. Duri ng the first
commissioning of the system the infrared light
curtains or light barriers shall be replaced by
jumpers.(See connection diagram 056632-45532)
Following the iearning cycle, the first closing cycle
and the parameterization of the control unit, the
infrared light curtains or light barriers have to be
connected and checked for proper functioning .
1.3.4 Insert the power plug and connect immediately
thereafter the rechargeable battery pack. (within max. 8 sec.)
.& The door must perform a closing cycle at low
(creep) speed.
If the door performs an opening cycle, the
system must be set back to original sellings.
Disconnect the power plug so that the opening
cycle stops.
Proceed on 2. original sellings
If the door performs a closing cycle, proceed with the
learning cycle starting with the door closed.
Please note:
The light barriers and radar motion detectors are
disabled during the learning cycle, as it has to be
performed without interruptions.
In case that a fauit or error should occur during this
procedure, the learning cycle will be interrupted and
needs to be started anew.
1.3.5 Performing the learning cycle:
ES200Easy.
press and hold SELECT button for 3 sec. Then the
door will perform a learning cycle.
ES200/ES 200-2D/ES 200 C048I DAC300:
press SERVICE button.
• Press and hold SERVICE/SELECT bullon until
the door commences with the learning cycle. The
external segments of the 7-segment display will
illuminate in turn.
• The door accelerates in order to determine the
door weight.
• The door opens at low (creep) speed to
determine the opening width.

Summary

Commissioning

Please Note

General notes and safety precautions for electrical equipment installation and power supply requirements.

Basic Requirements

Essential prerequisites for the operator, including assembly, connections, and end stop adjustments.

Update for Older Systems

Procedure for installing the ES 200 control unit as a replacement for older systems.

Door Safeguarding

Safety measures for safeguarding doors, especially in accordance with German DIN 18650.

First Commissioning Steps

Steps for initial system setup, including panel movement and program switch settings.

Learning Cycle

Detailed steps for performing the system's learning cycle to determine door parameters.

Country-Specific Settings

ES 200 C048 Commissioning

Commissioning steps for ES 200 C048, including belt tensioning and solenoid operation.

DAC 300 Commissioning

Commissioning steps for DAC 300, focusing on rubber belt tensioning and solenoid function.

Troubleshooting

Short Circuit Response

Explains control unit response to short circuits, including error codes and automatic restoration.

Fault Checklist

A checklist of common points to verify when faults occur during commissioning or operation.

Deleting Error Codes

Procedure for deleting error codes by setting the program switch to OFF.

Troubleshooting Specific Faults

Specific faults like learning cycle failure, jerky operation, and door remaining open.

Troubleshooting Specific Issues

Door Remains Open

Addresses the issue of the door remaining open in various program switch settings.

Error Code 1

Troubleshooting for error code '1' indicating obstruction during commissioning.

Door Fails to Open

Diagnoses why the door might not open with specific program switch settings.

Control Unit Error Code H

Troubleshooting for error code 'H' related to 2D door system and FST module.

ES 200 C048; DAC 300 Belt Issues

Specific checks for rubber belt operation issues in C048 and DAC 300 models.

Dorma ES 200 Easy Specifications

General

Adjustable Closing Speed	Yes
Hold-Open Function	Yes
Housing Material	Aluminum
Power Supply	230 V AC, 50/60 Hz
Closing Force	Adjustable
Latching Speed	Adjustable
Finish	Anodized aluminum
Standards	EN 16005
Closing Speed	10 - 50 cm/s (adjustable)