What to do if Doyon JA6SLG Oven does not turn on?
If your Doyon Oven isn't turning on, check the breakers on the front panel and the building's breakers. Also, ensure the doors are tightly closed. Inspect the motor breaker and overload relays in the electrical control panel.
Why is my Doyon JA6SLG not producing heat?
If your Doyon Oven isn't producing heat, first ensure the thermostat is set high enough to ignite the pilot light. If the oven blowers aren't running, check the overload relays in the control compartment; if disengaged, contact a qualified technician. If the blowers are running, confirm the manual shut-off valve is correctly opened. To restart, turn the thermostat to "OFF", wait 10 seconds, and reset to the desired temperature. Repeat up to three times; if it still fails, contact the company or a certified gas technician.
What to do if the OVERHEAT WARNING light is on in Doyon JA6SLG?
If the OVERHEAT WARNING light is illuminated and the buzzer sounds on your Doyon Oven, check for any obstructions to the cooling fan airflow. Verify that the cooling fan is operational; if it's not running, contact a qualified technician to replace it.
Why is my Doyon JA6SLG Oven baking unevenly?
Uneven baking in your Doyon Oven may be due to obstructed airflow from the grills, so ensure they are clear. Avoid using foil on the grills. Verify the oven temperature with a thermometer to match the thermostat setting. If the sides bake excessively, the fan might not be cycling correctly; confirm it turns 2.5 minutes in one direction, stops for 30 seconds, and then runs 2.5 minutes in the opposite direction.
What to do if Doyon JA6SLG steam device does not work properly?
If the steam device on your Doyon Oven isn't working correctly, ensure the oven has been heating for at least half an hour before use. Check that the building's water supply valve is open, and the oven's water needle valve is open one-eighth of a turn. Also, inspect the solenoid valve and the preset steam timer in the back control box. Ensure steam is injected while the fan is running, and the steam button light should illuminate during injection.
What to do if there is no humidity in Doyon proofer?
If there's no humidity in your Doyon proofer, check if the pilot light works when you set the humidity to high. If it does, verify water is entering the reservoir and inspect the water level switch box and float switch. Check for limestone obstructing water flow. If the float switch is working, check contactor P1 and the immersion element. If the pilot light doesn't light, verify the pilot light and the infinite switch.
What to do if there is no heat in Doyon proofer?
If there is no heat in the Doyon proofer, verify every breaker in front of the proofer. Check if the pilot light functions by raising the thermostat. If it does, verify the element. If it doesn't, verify the pilot light, thermostat, or contactors.
What to do if there is no light in Doyon proofer?
To address the absence of light in your Doyon proofer, start by verifying every breaker on the front of the proofer. Then, check the main proofer switch and the main proofer contactor.
What to do if steam button light inside Doyon Oven does not lite?
If the steam works in your Doyon oven, but the light inside the steam button does not illuminate, replace the inside button bulb light.
What to do if red light stays on in Doyon JA6SLG's water pan?
If the warning red light in the front control panel of your Doyon Oven stays on when the water pan is full (with the optional manual fill water pan feature), it indicates there is no more water in the principal water pan. Check if the water line is in an air lock condition. Disconnect the water line at the inlet of the green solenoid valve and clean the strainer filter. Also, clean the principal water pan and the float switch.
General| Power Type | Gas |
|---|---|
| Ignition | Electronic |
| Color | Stainless Steel |
| Pan Size | 18" x 26" |
| Oven Door | Glass |
To Next Page
