Dräger X-dock 6600 User Manual (English)

Other manuals for Dräger X-dock 6600

Questions and Answers:

H
hicksmeganAug 21, 2025
What to do if Dräger Docking Station has no communication with PC?
- T
  Tony GrantAug 21, 2025
  If your Dräger Docking Station isn't communicating with your PC, there are several things to check: * Ensure the Ethernet cable is correctly connected. If it is, and the problem persists, try replacing the Ethernet cable. * Verify that the IP address is configured correctly. If not, reconfigure it. * Confirm that the firewall isn't blocking data traffic. If it is, configure the firewall to allow communication.
H
hrossAug 22, 2025
Why Dräger Docking Station gas monitors do not pass the gas tests?
- J
  Jasmine RothAug 22, 2025
  If gas monitors are failing gas tests on the Dräger Docking Station because test gas isn't reaching the instrument, consider these potential causes: * Incorrect hose connections: Ensure all hose connections are properly connected. * Incorrect station gas configuration: Verify that the station gas configuration is correct. * Empty or closed test gas cylinder: Check the test gas cylinder to ensure it's neither empty nor closed. * Incorrectly set pressure regulator valve: Verify the setting of the pressure regulator valve.
L
Lauren WallaceAug 25, 2025
What to do if Dräger Docking Station does not start?
- H
  heatheralexanderAug 25, 2025
  If your Dräger Docking Station fails to start, it could be due to: * A disconnected power supply: Check all connections to the mains supply, power pack, and the station itself. * A defective power pack: If the connections are secure and the station still doesn't start, the power pack may be defective and require replacement.
L
Linda PowellAug 27, 2025
What to do if Dräger Docking Station does not recognize USB storage device?
- J
  Jennifer TranAug 27, 2025
  The formatting of USB storage devices varies, depending on the manufacturer. This applies to the file system (e.g. FAT32 or NTFS) as well as the partitioning. Dräger recommends using FAT32 and a partitioning that contains partitioning tables (USB-ZIP or USB-HDD).
C
coopertravisAug 27, 2025
What to do if Dräger Docking Station gas monitor not detected?
- M
  Morgan SpearsAug 27, 2025
  If a gas monitor isn't being detected by the Dräger Docking Station, consider the following: * The module might be dirty: Clean the module. * The instrument might be dirty: Clean the instrument. * The gas monitor SW version might be out of date: Update the gas monitor SW. If the issue persists, contact DrägerService as the module may be defective.
J
Jason SkinnerAug 29, 2025
What to do if Dräger Docking Station touchscreen does not respond?
- H
  Heather WilkinsAug 29, 2025
  If the Dräger Docking Station touchscreen isn't responding or has limited response, it might not be calibrated correctly anymore. Recalibrate the touchscreen.
T
Troy TaylorAug 31, 2025
Why Dräger Docking Station measuring chamber is leaky?
- A
  Andrew ThomasAug 31, 2025
  A leaky measuring chamber in the Dräger Docking Station may be caused by a dirty instrument and/or module. Clean the instrument and/or module. Alternatively, the seal may be worn and needs replacing.
A
amanda78Sep 1, 2025
What to do if Dräger Docking Station alarm element test not carried out?
- C
  chrisabbottSep 1, 2025
  If the alarm element test is not being carried out on the Dräger Docking Station, external light sources might be interfering with the test. Check for any interfering external light sources and reposition them or the station as needed.
R
russell07Sep 3, 2025
What to do if Dräger Docking Station shows module not found error?
- S
  Susan MullenSep 3, 2025
  The 'Module not found' or 'Wrong (incompatible) SW version' error message on the Dräger Docking Station can occur if a master is connected to modules with different software versions. In this case, a firmware update has to be performed via the master, even if the most current firmware is already installed on the master. Also, check whether all connections are correctly connected and screwed tight, because the electrical connection may be faulty.
O
ocollinsSep 5, 2025
What to do if Dräger Docking Station shows module X does not support firmware version error?
- K
  Kenneth CollinsSep 5, 2025
  If the Dräger Docking Station displays a 'Module X does not support firmware version' error, it means that the firmware version of the affected gas monitor is not compatible with the X-dock. Perform an update with the CC Vision PC software.

Dräger X-dock 6600 Specifications

General

Device Type	Calibration station
Supported Gases	Various gases depending on sensors used
Testing Functions	Calibration, bump test
Power Supply	100 – 240 VAC, 50/60 Hz
Storage Temperature	-20 to 60 °C
Weight	Approx. 4.5 kg
Data Logging	Yes
Connectivity	USB, Ethernet
Software	Dräger X-dock Software